Tektronix KEITHLEY 2450 Quick Start Manual Download Page 22

Page: 22 / 24

SMU Potentiostats and EC-UPGRADE Kit Quick Start Guide

071347302 / March 2020

End the test application

When you are finished making measurements, select

End App

to exit the test and return to normal SMU

operation.

Make sure to always select

Stop Test

before selecting

End App

Stop Test

turns off the

instrument's output.

Next steps

See the

Model 2450-EC, 2460-EC, and 2461-EC Potentiostats User's Guide

(document number 07711040x)

for detailed information on running the other test scripts included with your potentiostat or upgrade kit. The

guide is included on the supplied USB flash drive.

Additionally, see your Keithley Instruments 2450, 2460, or 2461 Interactive SourceMeter Instrument Reference

Manual for further details on using your SMU and running a test.

Summary of Contents for KEITHLEY 2450

























Search results

Summary of Contents for KEITHLEY 2450

Reviews:

Related manuals for KEITHLEY 2450

Brands by name

Popular brands

Tektronix KEITHLEY 2450, Quick Start Manual

Search results

Summary of Contents for KEITHLEY 2450

Reviews:

Related manuals for KEITHLEY 2450

Brands by name

Popular brands