Tektronix DPO2304SX Printable Help Download Page 547 | Manualshive

Page: 547 / 920

background image

4. If the instrument does not pass,

recalibrate the instrument, or have the
instrument serviced by qualified service
personnel.

NOTE. To always show the SPC status
icon or display a warning when SPC has
not been run in more than a month, click
the corresponding check box.

Calibration menu on DPO70000SX instruments

5. If the SPC needed icon is red, perform a

signal path compensation.

Check the color of the SPC Status icon:

■

Green indicates that SPC
successfully passed and the
temperature is stable.

■

Yellow indicates that the instrument
is in the warm up state or that it has
been over 30 days since SPC was
last run.

■

Red indicates that SPC needs to be
run (the temperature has varied
more than 5 °C, SPC failed, or SPC
has not been run).

Signal path compensation status

The following table lists the possible status messages for signal path compensation and the recommended action.

Status

Meaning and recommended action

Compensated

The instrument had warmed up, there were no failures during
the signal path compensation procedure, and the current
operating temperature is within 5 °C of the operating
temperature when the previous signal path compensation was
run.

Fail

One or more failures occurred during the signal path
compensation procedure. Contact your local Tektronix service
representative for further action.

Temp

The operating temperature is not within 5 °C of the previous
signal path compensation.

Warming up

The instrument has not warmed up. Wait for the instrument to
complete its warm up period before running the signal path
compensation procedure.

Vertical setups

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

515

«
...
545
546
547
548
549
...
»

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DPO2304SX

FX-ARM CONTROLLER

Brand: Magicfx Pages: 16

WJHD100 - DIGITAL DISC RECORDE

Brand: Panasonic Pages: 7

Brand: CAMAG Pages: 40

Brand: Mainca Pages: 21

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: XM Fitness Pages: 10

Brand: Garmin Pages: 2

Brand: HABYS Pages: 16

Brand: Velp Scientifica Pages: 12

Brand: Yamaha Pages: 24

Brand: J&M Pages: 33

Brand: EuroLite Pages: 28

Brand: VADDIO Pages: 58

Contrology Cadillac

Brand: Balanced Body Pages: 7

TR 2B INC INT NC

Brand: OMGA Pages: 76

Brand: Costan Pages: 154

Ology Walkstation 1451458001

Brand: Steelcase Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands