manualshive.com logo in svg

Tektronix CFG253, Service Procedures

Share
Download
Tektronix CFG253 Service Procedures Download Page 4

CFG253

Performance Verification & Adjustment Procedures

Page 4 of 19

Procedure #: CP1005   Revision: A

2.

CHECK MAIN OUTPUT AMPLITUDES

a.

Set-Up:

AMPLITUDE

CW

DC OFFSET

Pushed In

RANGE

1K

FUNCTION

Triangle

VOLTS OUT

Button Out

FREQ/10

Button Out

FREQ DIAL

3.0

b.

Test Scope Set-Up:

Volts/Div

2V

Time/Div

0.2 mSec

c.

Connect MAIN OUTPUT to test scope vertical input via coax cable and 50 ohm
terminator.

d.

Check the test scope display for > 5 divisions (10V).

e.

Rotate the AMPLITUDE knob to nearly CCW.

f.

Set test scope to 10 mV/Div.  Check that the display reduces to less than 5
divisions (50mV) as the AMPLITUDE knob approaches the CCW stop.

g.

Set the VOLTS OUT button in and change the test scope Volts/Div to 5mV.

h.

Check for a display of < 1 division (5mV) as the knob approaches the CCW stop.

i.

Set the test scope Volts/Div to 0.2 V.  Rotate the AMPLITUDE knob fully CW.

j.

Check the display for > 5 divisions (1V).

k.

Return the VOLTS OUT button to the out position and ensure that the
AMPLITUDE is CW.

Summary of Contents for CFG253




















Reviews:

No comments

Brands by name

Popular brands

Load more brands