manualshive.com logo in svg

Tektronix CFG253, Service Procedures

Share
Download
Tektronix CFG253 Service Procedures Download Page 15

CFG253

Performance Verification & Adjustment Procedures

Page 15 of 19

Procedure #: CP1005   Revision: A

5.

Square Wave Overshoot, Rise Time and Fall Time

a.

Test Scope Set-Up:

Volts/Div

5V

Time/Div

0.5 uSec

Trig Slope

+

b.

Set-Up:

AMPLITUDE

CW

DC OFFSET

Pushed In

RANGE

100K

FUNCTION

Square Wave

VOLTS OUT

Button Out

FREQ/10

Button Out

FREQ DIAL

3.0

c.

Connect MAIN OUTPUT to test scope vertical input via coax cable WITHOUT
the 50 ohm terminator.

d.

Adjust AMPLITUDE knob for a 4 division display on the test scope.

e.

Adjust C31 for minimum overshoot (will not be completely flat).

f.

Set Time/Div to 50 nSec/Div.  Adjust Trig Level control as necessary to display
the rising edge of the Square Wave.

g.

Check risetime between the 10% and 90% points for < 100 nSec (2 Div).

h.

Set test scope Trig Slope to - (negative).  Adjust Trig Level to view the Falling
edge of Square Wave.

i.

Check the Fall Time between the 10% and 90% points for < 100 nSec (2 Div).

6.

Set OUTPUT Levels

a.

Set-Up:

AMPLITUDE

CW

DC OFFSET

Pushed In

RANGE

1K

FUNCTION

Triangle

VOLTS OUT

Button Out

FREQ/10

Button Out

FREQ DIAL

3.0

Summary of Contents for CFG253




















Reviews:

No comments

Brands by name

Popular brands

Load more brands