manualshive.com logo in svg

Tektronix CFG253, Service Procedures

Share
Download
Tektronix CFG253 Service Procedures Download Page 17

CFG253

Performance Verification & Adjustment Procedures

Page 17 of 19

Procedure #: CP1005   Revision: A

c.

Set the Distortion Analyzer INPUT RANGE to Auto Range and the FUNCTION
settings to Volts, Auto Range and THD+N.

d.

Adjust R43 and R46 for a minimum distortion reading on the Distortion
Analyzer.  Repeat the two adjustments as necessary to obtain the optimum
results.

e.

Disconnect the cable from the Distortion Analyzer.

*** Alternate Procedure ***

( If Distortion Analyzer is not available )

f.

Test Scope Set-Up:

Volts/Div

2V

Time/Div

1 uSec

g.

Connect MAIN OUTPUT to test scope vertical input via coax cable and 50 ohm

terminator.

h.

Adjust R46 for minimum distortion at top of sinewave and R43 for minimum
distortion at the bottom.

7.

FREQUENCY DIAL ACCURACY

a.

Set-Up:

AMPLITUDE

CW

RANGE

1K

FUNCTION

Triangle

VOLTS OUT

Button In

FREQ/10

Button Out

FREQ DIAL

3.0

b.

Connect the MAIN OUTPUT to the input of a Frequency Counter.

NOTE:

If a Frequency Counter is not a available, see
alternate procedure on next page.

c.

Adjust R6 for a reading of 3.0 KHz on the Frequency Counter.

Summary of Contents for CFG253




















Reviews:

No comments

Brands by name

Popular brands

Load more brands