Troubleshooting
Table 4-7: Calibration error codes (cont.)
Error code
Error log message
Possible defect
on board
Note
263XY1108
Invalid phase transition distance at CH2, TEK0015-X
bit Y.
AWG12G
AWG12G: U100B, U300B (X=0,1
-> P; X=2,3 -> Q; X=4,5 -> R; X=6,7
-> S; X=8,9 -> T)
270000000
HwExecYigCal PLL read error
AWG12G
AWG12G: U1000, U1040
270000001
HwExecYigCal PLL 6GHz offset under 2048 vtune=xxxx
CLK12G
CLK12G:U3200, U3250, Y3280
270000002
HwExecYigCal PLL 6GHz offset under
fl
ow vtune=xxxx
CLK12G
CLK12G:U3200, U3250, Y3280
270000003
HwExecYigCal PLL 6GHz tuning under
fl
ow vtune=xxxx
CLK12G
CLK12G:U3200, U3250, Y3280
270000004
HwExecYigCal PLL 6GHz tuning under
fl
ow vtune=xxxx
CLK12G
CLK12G:U3200, U3250, Y3280
270000005
HwExecYigCal PLL 12GHz tuning over 4095
vtune=xxxx
CLK12G
CLK12G:U3200, U3250, Y3280
270000006
HwExecYigCal PLL 12GHz tuning over
fl
ow vtune=xxxx
CLK12G
CLK12G:U3200, U3250, Y3280
271000001
HwExecYigCal PLL 6GHz offset under 2048 vtune=xxxx
CLK12G
CLK12G: U3200, U3250, Y3280
271000002
HwExecYigCal PLL 6GHz offset under
fl
ow vtune=xxxx
CLK12G
CLK12G: U3200, U3250, Y3280
271000003
HwExecYigCal PLL 6GHz tuning under
fl
ow vtune=xxxx
CLK12G
CLK12G: U3200, U3250, Y3280
271000004
HwExecYigCal PLL 6GHz tuning under
fl
ow vtune=xxxx
CLK12G
CLK12G: U3200, U3250, Y3280
271000005
HwExecYigCal PLL 12GHz tuning over 4095
vtune=xxxx
CLK12G
CLK12G: U3200, U3250, Y3280
271000006
HwExecYigCal PLL 12GHz tuning over
fl
ow vtune=xxxx
CLK12G
CLK12G: U3200, U3250, Y3280
272000000
Clock Power CAL failed
272000001
Clock Power CAL failed at 6 GHz
272000002
Clock Power CAL failed at 12 GHz
290000000
Marker Level Calibration has not been completed.
N/A
290000001
Marker cross point calibration result exceeds limit.
OUT10G
OUT10G: U120, U170
290X00000
Marker Level Calibration has not been completed at
CHX.
N/A
290XY0001
Marker cross point calibration result exceeds limit at
CHX, MARKER Y.
OUT10G,
AWG12G
OUT10G: U120/170, U470/480,
J100/110/150/170 AWG12G:
J110A/111A/115A/
116A/110B/111B/115B/116B
290XY0002
Marker cross point calibration couldn’t be converged on
-1.0V at CHX, MARKER Y.
OUT10G,
AWG12G
OUT10G: U120/170, U470/480,
J100/110/150/170 AWG12G:
J110A/111A/115A/
116A/110B/111B/115B/116B
291000000
Marker Level Calibration has not been completed.
N/A
291000001
Marker cross point calibration result exceeds limit.
N/A
291X00000
Marker Level Calibration has not been completed at
CHX.
N/A
AWG7000B and AWG7000C Series Service Manual
4–71
Summary of Contents for AWG7 1B Series
