manualshive.com logo in svg

Tektronix 82A04B, User Manual

Share
Download
Tektronix 82A04B User Manual Download Page 17

Operating basics

Using extender cables with the 82A04B

You can install an 80X01 (1 meter) or 80X02 (2 meter) electrical
sampling module extender cable on the 82A04B to provide correct phase
reference clock signal alignment for different sampling module setups:

Always use the 80X02 cable provided with the 82A04B when using

remote sampling modules 80E07B, 80E08B, 80E09B or 80E10B

Always use the same extender cable length to extend the 82A04B

as you use for extending supported monolithic sampling modules
(such as the 80E01, 80E03, 80E04, or 80E11X1). For example, if
you use an 80X01 extender cable with an 80E11X1, also use an
80X01 extender cable with the 82A04B.

Refer to the

80X01 and 80X02 Electrical Sampling Module Extender

Instructions

(Tektronix part number 071-3206-xx) for more information

on using extender cables with modules.

NOTE.

Legacy module extender cable 80N01 can be used to extend

supported sampling modules and the 82A04B. The 80N01 cable is
equivalent to the 80X02 extender cable.

82A04B User Manual

7

Summary of Contents for 82A04B
























Reviews:

No comments

Brands by name

Popular brands

Load more brands