Checks and Adjustment—7T11A
Part II—
Performance Check and Adjustment
C2.
CHECK
LOW-FREQUENCY TRIGGERING
C3.
CHECK
MEDIUM-FREQUENCY TRIGGERING
NOTE
First
perform step
C1,
then proceed.
NOTE
If the
previous step was
not performed, first perform
step C1.
C2. SETUP CONDITIONS
C3.
SETUP CONDITIONS
7T11A Controls:
INT pushbutton
...............................................................
Pressed in
TRIG
AMP X1 pushbutton.................................... Pressed in
SWEEP
RANGE..................................................................... 5 ms
TIME/DIV
......................................................
1 ms
IN TABLE 5-9)
Test Equipment Controls:
Low
Frequency Sine
Wave Generator
Frequency
.......................................
Sampling
Unit
Units/Div
.........................................
7T11A Controls:
INT
pushbutton.................................... Pressed in
TRIG
AMP X10 pushbutton.........................................
Pressed in
SWEEP
RANGE................................................................................5 µS
TIME/DIV............................................. 10 ns
18-INCH
ATTENUATOR
BNC
CABLES
Test Equipment
Controls:
Medium
Frequency
Sine Wave
Generator
Frequency
..............................................
Sampling
Unit
Units/Div
................................................
a. CHECK—7T11A low-frequency
triggering capability
by
using the control settings and requirements
given in Ta
ble
5-9
to
obtain a
stable, triggered display. The signal gen
erator output
amplitude is correct
when its
signal causes the
amount of vertical deflection
shown under the display size
column.
Add
a 10X BNC Attenuator to the 7T11A
trigger
signal as
indicated
in the right-hand column of Table 5-9.
Set 7T11A
STABILIY and TRIG LEVEL as necessary for a
stable
display. On real-time ranges, TIME
POSITION also
aids
in
stabilizing triggering. Changes
in control settings be
tween
successive steps are indicated
in the table with an
asterisk.
NOTE
To check
internai triggering from
the mainframe's
other
vertical
compartment, an additional Sampling
Unit may be
installed
and the internal
triggering steps
repeated
for
that compartment.
a. CHECK—7T11A
medium-frequency triggering ca
pability by
using the control settings and requirements given
in
Table 5-10 to obtain a
stable, triggered display. The signal
generator output
amplitude is correct when its signal causes
the
amount
of vertical deflection
shown under the Display
Size
column.
Set 7T11A
STABILIY and TRIG LEVEL as
necessary for
a
stable
display.
Add
a 10X BNC Attenuator
to
the
7T11A trigger
signal as
indicated in the right-hand
column
ot Table 5-10. Changes in control settings between
successive steps are
indicated
in the table with an asterisk.
5-44
Summary of Contents for 7T11A
