background image

73A–308

Page 64

28. The voltage at the remaining 4 pins shown in Table 1–2 will be less than +500 mV.

29. Send “QRB

lf

30. Read “000000000000000000F0

crlf

31. Send “O4

lf

” (Open 4) to the 73A-308.

32. Use a DMM and measure the voltage at BITs 0–1, 0–2, 0–4, 0–8, and 1–1 (refer to

TABLE 4–1). The voltage on these pins will be the same as the +5 V source.

33. The voltage at the remaining 3 pins shown in Table 1–2 will be less than +500 mV.

34. Send “QRB

lf

35. Read “000000000000000000E0

crlf

36. Send “O5

lf

” (Open 5) to the 73A-308.

37. Use a DMM and measure the voltage at BITs 0–1, 0–2, 0–4, 0–8, 1–1, and 1–2 (refer

to Table 1–2). The voltage on these pins will be the same as the +5 V source.

38. The voltage at the remaining 2 pins shown in Table 1–2 will be less than +500 mV.

39. Send “QRB

lf

40. Read “000000000000000000C0

crlf

41. Send “O6

lf

” (Open 6) to the 73A-308.

42. Use a DMM and measure the voltage at BITs 0–1, 0–2, 0–4, 0–8, 1–1, 1–2, and 1–4

(refer to Table 1–2). The voltage on these pins will be the same as the +5 V source.

43. The voltage at the remaining pin shown in Table 1–2 will be less than +500 mV.

44. Send “QRB

lf

45. Read “00000000000000000080

crlf

46. Send “O7

lf

” (Open 7) to the 73A-308.

47. Use a DMM and measure the voltage at all eight BITs (refer to Table 1–2). The

voltage on these pins will be the same as the +5 V source.

48. Send “QRB

lf

a. Read “00000000000000000000

crlf

Summary of Contents for 73A-308

















































































Reviews: