background image

73A–308

Page 60

Table 1–1: Equipment Required (Cont.)

Required tools and equipment

Part number

Digital Multi Meter (DMM)

standard lab equipment

+50 V POWER SUPPLY capable of 300ma

standard lab equipment

+5 V Power supply capable of 2.5A

standard lab equipment

15 

 3 Watt 5% Resistor, requires 8 resistors

n/a

165 

 3 Watt 5% Resistor

n/a

Talker/Listerner (Send/Read) program with the capability
to send out word

n/a

Serial commands

n/a

Performance Verification Procedure

Default Conditions

1. Shut the VXI system down, and then power up the VXI system and wait 10 seconds.

2. Only the green PWR LED will be lit, if this is not true, repeat step 1.

3. Send a “QER

lf

” (Query ERrors) to the 73A-308.

4. Read “NO ERRORS

crlf

5. Send “QEN

lf

” (Query Enable/disable status) to the 73A-308.

6. Read “0

crlf

7. Send “QRB

lf

” (Query Read Back status) to the 73A-308.

8. Read “00000000000000000000

crlf

9. Send “QTG

lf

” (Query TriGger status) to the 73A-308.

10. Read “0

crlf

LED Test

1. Remove power from the VXI system, then reapply power. The FAIL LED will be

briefly lit in red during power up.

2. When the following command is sent to the 73A-308, the MSG LED will flash for

about a half second.

a. Send “R

crlf

” (Reset)

Summary of Contents for 73A-308

















































































Reviews: