APPENDIX C
REPAIR PARTS LIST
C-1. This appendix provides a list of repair parts for maintenance support
of the equipment.
The parts along with their descriptions are listed in
table C-1 below.
C-2. Instructions for requisitioning parts not identified by Federal Stock
Numbers require the following information be furnished to the Supply Officer:
a. Manufacturer's
b. Manufacturer’s
c. Manufacturer’s
Federal Supply
identification
nomenclature
Code Number
number
d. My other information as listed on parts list that will aid in
identification of the item being requisitioned.
C-3. If DD Form 1348 is used, fill in all blocks except 4, 5, 6 and Remarks
field in accordance with AR 725-50.
Complete Form as follows:
a. In Blocks 4, 5 and 6 list Manufacturer’s Federal Supply Code Number
followed by a colon and the Manufacturer’s part number.
b. Complete Remarks Field as follows:
Nomenclature of the repair part
and any other identification to assist Supply Officer in procurement.
C-4. Report of errors, omissions and recommendation for improving this
publication by the individual user is encouraged. Reports should be sub-
mitted on DA Form 2028 (Recommended Changes to DA Publications) and forwarded
direct to Commanding Officer, Frankford Arsenal, ATTN: AMSWE-SMF-W3100,
Philadelphia, Pa. 19137.
C-1
Summary of Contents for 491
