background image

9.  Use  your  turn  signals,  checking  for  traffic  well  in  advance  of  turning

If  the  tractor  is  not 

equipped  with  turn  signals  and  law  requires  them,  install  them  prior  to  operating  on  or  near 
public roads. 
 
 

Safety Decals 
 

1. Keep decals clean. Remove dirt with a wet clean cloth when necessary. 
2. Replace safety decals if destroyed, missing, painted over or unreadable. If any safety decals 
are  covered  or  obscured  when  the  ROPS  is  mounted,  it  is  recommended  that  you  purchase 
replacement  decals  from  the  tractor  manufacturer.  Mount  them  in  a  readable  location  at,  or 
near, their original location before operating the tractor. 
3. New ROPS decals and tractor decals are available from your tractor dealer. 
 
 

ROPS Safety 
 

1. Install the ROPS in accordance with Tektite mounting instructions. Failure to do so may affect 
the ROPS ability to withstand a roll over.  
2. If the ROPS is subjected to alteration, structural damage or involved in an over turn accident, 
the entire structure must be replaced. Failure to do so may result in injury or death in the event 
of a roll over. 
3. If the tractor in not equipped with seat belts, purchase approved seat belts from the tractor 
manufacturer or Tektite prior to operating the tractor. 
4. Always fasten seat belts prior to operating the tractor. 
5. Always operate the tractor from the 

operator’s seat.

 

6. Remove mud, crop residue, chains and 

tools from steps and operator’s

 platform. They may 

interfere with pedal operation or entry/exit from the tractor. 
7. Remove all loose chains, tools, and equipment from the 

operator’s platform

. Failure to do so 

may cause injury or death in the event of a roll over. 
8. Do not install the ROPS on a tractor model that the ROPS is not designated for (compatible 
tractor  designations  are  printed  on  the  ROPS  serial  number  plate).    The  ROPS  is  designed 
specifically for individual models to ensure ROPS requirements will be met. Installing the ROPS 
on a non designated tractor may result in injury or death. 
 
 

Emergency Exits 
 

This ROPS cab has 2 exits, which may be used in an emergency: left and right doors. 
 
 

 

    June 2021© Kioti CK35 Series ROPS Cab Operation Manual

Summary of Contents for Kioti CK35 Series


























Reviews: