Teknoware TAPSA CONTROL TKT65 Page 2 Installation And Maintenance Instructions Manual Download

Page: 2 / 53

VOT 34; Rev 1.81; EN; 11.12.2019

TKT65C

– Installation and maintenance

Table of contents

Table of contents ................................................................................................................ 2

1. Safety instructions ......................................................................................................... 4

2. Package contents and storing ....................................................................................... 4

2.1 Contents of package

................................................................................................................. 4

2.2 Storing

......................................................................................................................................... 4

3. Product description ........................................................................................................ 5

3.1 Manufacturer

.............................................................................................................................. 5

3.2 Terminology

............................................................................................................................... 5

3.3 Type

............................................................................................................................................. 5

3.4 Explanation of letters (in previous models)

........................................................................... 5

3.5 List of optional features

............................................................................................................ 5

3.6 General description

................................................................................................................... 6

3.7 Technical specifications

........................................................................................................... 7

3.8 Directives and standards

.......................................................................................................... 8

4. Description of operations .............................................................................................. 9

4.1 Purpose of the central battery unit

.......................................................................................... 9

4.2 Circuit outputs

........................................................................................................................... 9

4.3 Circuit board settings

................................................................................................................ 9

4.4 Control unit

................................................................................................................................. 9

Individual luminaire monitoring test with basic settings

........................................................................................... 10

Circuit monitoring luminaire test with basic settings

................................................................................................ 10

4.5 Operation of the central battery unit

..................................................................................... 10

4.6 Normal Status

........................................................................................................................... 10

4.7 Central module panel

.............................................................................................................. 11

4.8 Control Module panel luminaire monitoring LEDs and menu settings

............................. 13

4.9 Control Module panel test functions and alarms

................................................................ 19

4.10 Buttons

.................................................................................................................................... 21

5. Central battery system planning and installation ...................................................... 22

5.1 System planning

...................................................................................................................... 22

Luminaire-specific addressable monitoring

.............................................................................................................. 22

Circuit monitoring

..................................................................................................................................................... 22

5.2 System installation

.................................................................................................................. 22

Parts layout

................................................................................................................................................................ 23

DIP switch settings in circuit boards

......................................................................................................................... 24

5.3 Commissioning

........................................................................................................................ 25

Setting of battery capacity

......................................................................................................................................... 25

Turning the power ON for the first time

................................................................................................................... 26

Forced charging of the batteries

................................................................................................................................ 26

Checking the luminaire circuits one at a time

........................................................................................................... 27

Configuration

............................................................................................................................................................ 27

Summary of Contents for TAPSA CONTROL TKT65






















































Search results

Summary of Contents for TAPSA CONTROL TKT65

Reviews:

Related manuals for TAPSA CONTROL TKT65

Brands by name

Popular brands

Teknoware TAPSA CONTROL TKT65, Installation And Maintenance Instructions Manual

Search results

Summary of Contents for TAPSA CONTROL TKT65

Reviews:

Related manuals for TAPSA CONTROL TKT65

Brands by name

Popular brands