Teknik 5426509 Manual Download

Page: 24 / 29

Step 20

Page 24

With the palm of

your hand, tap

the DRAWER

BOTTOM down

into the groove.

Fasten the DRAWER BACK (D78) to the DRAWER SIDES (D14 and D15).

Use four BLACK 1-9/16" FLAT HEAD SCREWS (30S).

NOTE: Be sure the DRAWER BOTTOM (D716) inserts into the groove of

the DRAWER BACK (D78).

Insert the DRAWER SIDES (D14 and D15) at an angle

into the slot at each end of the DRAWER FRONT (N).

Slide the DRAWER BOTTOM (D716) into the grooves in the

DRAWER SIDES (D14 and D15) and DRAWER FRONT (N).

The tabs should insert freely

into the slots. Gently tilt the

DRAWER SIDES side to side

until the tabs slip into the slots.

Groove

30S

Start each screw a few turns before

completely tightening any of them.

BLACK 1-9/16" FLAT HEAD SCREW

(4 used in this step)

Be sure the DRAWER

BOTTOM inserts into the

DRAWER FRONT groove.

D15

D716

D15

D716

D14

D78

Unfinished

surface

Be sure the

DRAWER

BOTTOM

inserts into

the DRAWER

BACK groove.

Summary of Contents for 5426509






























Search results

Summary of Contents for 5426509

Reviews:

Related manuals for 5426509

Brands by name

Popular brands

Teknik 5426509, Manual

Search results

Summary of Contents for 5426509

Reviews:

Related manuals for 5426509

Brands by name

Popular brands