background image

 

3 of 20 

 © 2009 

  D 512 - 09/09

AUXILIARY SENSORS

The thermostat has a single built-in sensor to measure air temperature at the thermostat. In 
addition to the built-in sensor, the thermostat has terminals to connect up to two separate 
sensors. These sensors can be either indoor sensors, slab sensors, a remote sensor, or 
an outdoor sensor.

Indoor Sensor

An indoor sensor is used to measure the air temperature in the zone that the thermostat 
is controlling. The temperature being read by the indoor sensor is used in the calculations 
of the on times for the relay(s) in the thermostat. Either one or both of the auxiliary sensor 
inputs can be configured for indoor sensors. This setting is made through the Adjust menu 
of the thermostat. If more than one sensor, either the built-in sensor or an auxiliary sensor 
set as an indoor sensor, is being used to measure the zone temperature, the temperature 
of the active sensors is averaged and used to calculate the on time of the relay(s).

Slab Sensor

A slab sensor is used to measure the slab temperature in the zone that the thermostat 
is controlling. The temperature being read by the slab sensor is used in the calculations 
of the on time for the Heat relay and allows the thermostat to operate the slab between 
the slab minimum and slab maximum settings. If more than one slab sensor is used, the 
slab temperatures are averaged by the thermostat.

Remote Sensor

A single remote sensor can be connected to the thermostat. The temperature 
measured by a remote sensor does not affect the on time of the relays and is only 
used for display purposes.

Outdoor Sensor

A single outdoor sensor can be connected to the thermostat. The temperature measured 
by an outdoor sensor does not affect the on time of the relays and is only used for display 
purposes.

ACCESS LEVELS

The tekmar Programmable Thermostat has two 
access levels. These access levels restrict the 
number of items available in the menus of the 
thermostat. The two access levels are User and 
Installer. This selection is made using the DIP 
switch located on the circuit board inside the 
thermostat.

The Installer access level allows the installer to 
adjust all of the settings in the thermostat including 
those required to match the thermostat to the 
mechanical system and the devices used.

The User access level allows the end user to 
adjust the time, temperatures and schedules used 
by the thermostat.

Po

w

er

: 2

± 1

0%

 60 Hz 3 V

A

Re

la

y:

 24

 V (

ac) 2 

A

 

Class 2

938-

02

51

2

Switch Se

ttings

:

Ins

taller/User

2 Stag

e/Heat-

Cool

Made in Canada Mee

ts Class B:

Canadian ICES FCC P

ar

t 1

5

Dip Switch

Summary of Contents for D 512





















Reviews: