Teka BKSSL BPM Safety And Installation Instructions Manual Download Page 5 | Manualshive

Page: 5 / 9

background image

IMPORTANT SAFETY INFORMATION LISTED ON REVERSE

READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS

DATE

5-14-18

40429 Brickyard Drive • Madera, CA 93636 • USA

559.438.5800 • FAX 559.438.5900

www.tekaillumination.com • [email protected]

REFERENCE NUMBER

INS-2569-01

BEACON POLE MOUNT™ (BPM)

Hinge Base Installation Instructions

7. Make watertight connections using waterproof

wire connectors to connect fixture leads to

secondary leads from driver. Leave length for

future service.

See wiring diagram.

8. Slide fixture over pole top. Secure with four (4)

1/4-20 screws using /1/8” Allen wrench. Make

sure the fixture is completely seated. Do not

overtighten.

«
...
3
4
5
6
7
...
»

Summary of Contents for BKSSL BPM










Reviews:

No comments

Related manuals for BKSSL BPM

Brand: L-Sniper Pages: 12

Brand: R.V.R. Elettronica Pages: 38

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

Brand: Messoa Pages: 32

Brand: Nady Systems Pages: 8

Brand: Parkside Pages: 54

Brand: TAD Pages: 2

Brand: Taco Pages: 56

Aventage RX-A3040

Brand: Yamaha Pages: 8

Brand: Yamaha Pages: 4

Brand: Yamaha Pages: 8

LevelPro ProScan 3 Series

Brand: ICON Pages: 14

Level pro 200C Series

Brand: ICON Pages: 19

Brand: Fenton Pages: 16

Brand: Aiwa Pages: 20

JV-B765HV9V22DNR

Brand: JV vision Pages: 12

Brand: NAPCO Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands