TECO N3 Series Operating Manual Download Page 108

Page: 108 / 115

N3 Drive Operations Manual

Appendix D-

N3 Cover Removal Frames 4, 5 & 6

Main

Cover

Digital

Operator

Conduit

Box

Cover

“A”

Mounting

Screws

(2)

“B”

Mounting

Screws

(2)

Charge

Indicating

Lamp

Finger

Removal

Grips
(Both

sides)

Cover Removal Procedure

– First remove the Digital Operator by gripping at

the points shown and pulling

straight

out. (The

Operator has a connector that plugs directly into
to the chassis.)
2

– Loosen both mounting screws “A” and back

out but do not remove.
3

– Loosen and remove both mounting screws “B”.

– Slide the main cover up and lift off.

– The conduit box cover if needed may be

removed in essentially the same way.

Cover Replacement

– Slide the main cover screw slots over screws “A”

and set in place.
2

– Insert and tighten screws “B” and then tighten

screws “A”.
3

– Next insert the Digital Operator by carefully lining

up the connector and pushing

straight

in.

– Replace the conduit box cover if it was removed.

Fig. AD.4 Cover Removal for N3 Frame Sizes 5 & 6

Cover

Digital

Operator

Mounting

Screws

Finger Removal

Grips

(Both sides)

Cover Removal Procedure

– First remove the Digital Operator by gripping at

the points shown and pulling

straight

out. (The

Operator has a connector that plugs directly into
to the chassis.)
2

– Loosen the four mounting screws and lift off the

cover.

Cover Replacement

– Set the cover in place and secure with the four

mounting screws.
2

– Next insert the Digital Operator by carefully lining

up the connector and pushing

straight

in.

Mounting

Screws

(4)

Fig. AD.3 Cover Removal for N3 Frame Size 4

Summary of Contents for N3 Series




















































































































Search results

Summary of Contents for N3 Series

Reviews:

Related manuals for N3 Series

Brands by name

Popular brands

TECO N3 Series, Operating Manual

Search results

Summary of Contents for N3 Series

Reviews:

Related manuals for N3 Series

Brands by name

Popular brands