Tecnoware EVO DSP TM User Manual Download

Page: 17 / 44

UPS EVO DSP TT

User’s Manual

4.1.2 Mimic Panel

Mimic panel is a diagram, which shows the path of energy flow in the UPS by means of several LED’s.
Definitions of LED status are shown below:

LED's

COLOR

DEFINITION

STATE

Line 1

Green

Input mains voltage is OK and Rectifier is active.

Steady

Input mains voltage is OK and Rectifier is inactive.

Flashing

Input mains voltage is very close to its upper/lower limit and Rectifier
is active.

Input mains voltage is not OK.

Off

Line 2

Green

Bypass voltage is OK.

Steady

Bypass voltage is not OK and output voltage is synchronized to the
Bypass voltage.

Flashing

Bypass mains voltage is not OK and output voltage is not synchronized
to the Bypass voltage.

Off

Battery Red

Battery mode is active and battery voltage is OK.

Steady

UPS is performing Battery Test and battery voltage is OK.

Battery mode is active and battery voltage is close to its lower limit
(energy available in the battery is about to be depleted).

Flashing

Battery Test is active and battery voltage is close to its lower limit
(energy available in the battery is about to be depleted).

Rectifier is active and able to supply whole power required by the
Inverter.

Off

Inverter Green

Load is fed via Inverter.

Steady

Inverter is not active.

Off

Load

Green

Load is powered.

Steady

Load is powered but UPS is overloaded.

Flashing

Output voltage is not OK.

Off

Bypass

Yellow

Load is fed via static Bypass line.

Steady

Bypass is not active.

Off

Fault

Red

No alarms.

Off

A minor priority alarm is present.

Flashing

A major priority alarm is present.

Steady

Summary of Contents for EVO DSP TM













































Search results

Summary of Contents for EVO DSP TM

Reviews:

Related manuals for EVO DSP TM

Brands by name

Popular brands

Tecnoware EVO DSP TM, User Manual

Search results

Summary of Contents for EVO DSP TM

Reviews:

Related manuals for EVO DSP TM

Brands by name

Popular brands