background image

 

User’s manual 

8

 

UPS EXA LCD  1.5 – 2-0 – 2.6 

 

5

 

Electrical Installation and First Start Up 

We advise you to follow the steps below explained for greater safety: 

1.

 

Switch  off  all  the  devices  (Personal  Computer  or  other  electronic  devices)  that  need  to  be  supplied  by  the 
UPS. 

2.

 

Connect  the  UPS  Input  socket  to  the  AC  line  outlet  Through  the  Personal  Computer  supplying  cable. 

It  is 

mandatory to ground the AC line outlet according to the Safety Standards

. Carefully check the grounding, 

make sure that the utility power is available, and that its range falls within the UPS specifications (refer to 
the “Specifications” chapter). 

3.

 

Press the 

ON/OFF

 button on the front panel: the UPS emits a brief acoustic signal, turns the LCD display on, 

and performs a 

functioning SELF-TEST

. After some seconds the UPS starts to work in 

Normal mode

: the 

AC 

MODE

  icon  is  on.  Leave  the  UPS  in  Normal  mode  for  at  least  4  hours  in  order  to  completely  recharge  the 

batteries. 

4.

 

Switch the UPS off (by pressing again the ON/OFF button). 

5.

 

Connect  the  devices  to  be  supplied  to  the  UPS  outputs,  by  using  only  the  included  cables.  Be  sure  all  the 
devices have the main switch in ON position. 

6.

 

Turn  on  the  UPS  again.  Check  that  it  starts  working  correctly  and  it  doesn’t  signal

 

any  sort  of  anomaly. 

Moreover  be  sure  that  all  the  devices  connected  to  the  UPS  outputs  are  working  correctly.  By  LCD  display 
check if the Output load percentage is less than 100%; otherwise it is necessary to remove part of the Output 
load.  

7.

 

Simulate a black-out by removing the AC Input line. The UPS starts working in 

Battery mode

: the 

AC MODE

 

icon is off and the BATTERY MODE icon is on. Moreover the UPS emits a brief acoustic signal every 10 seconds. 

8.

 

Be sure that all the devices connected to the UPS outputs are working correctly and the UPS doesn’t signal

 

any sort of anomaly. 

9.

 

Restore the AC Input line: after few seconds the UPS turns back in Normal mode. 

 

Before using EXA LCD normally, leave it in Normal mode in order to charge the batteries completely as specified at 
point 3. The batteries reach the 90% of their capacity after about 4 hours of recharge. 

 

 

It is compulsory to ground/earth the UPS according to the Safety Standards. 

Risk  of  electric  shock  at  the  Output  lines  if  the  UPS  is  ON,  even  when  the  UPS  is  not 
connected to AC utility line. 

Risk  of  electric  shock  at  the  Output  lines  while  the  unit  is  connected  to  the  AC  utility 
line. 

Risk of electric shock: do not remove the cover. The UPS contains internal parts, which 
are at a high Voltage and are potentially dangerous, capable of causing injury or death 
by electric shock. 

There  are  no  internal  parts  in  the  UPS  that  are  user  serviceable.  Any  repair  or 
maintenance  work  must  be  performed  exclusively  by  qualified  technical  personnel 
authorized  by  TECNOWARE.  TECNOWARE  declines  any  responsibility  if  this  warning  is 
disregarded. 

Disregard for these warnings may lead to a risk of electric shock to operators. 

 

Summary of Contents for ERA LCD 0.65





















Reviews: