Tecnik CF-MTL-2401 User Manual Download Page 8

Page: 8 / 15

www.tecnikchargers.com

CF-MTL-42401

208/240V

480V

Congure the A.C. input adjustment by changing the postion of the
three (3) metal jumpers on the six (6) position terminal block.

* Do not move any wires, only the metal jumpers

208/240V

480V

CF-MTL-42403

Congure the A.C. input adjustment by changing the postion of the
three (3) metal jumpers on the nine (9) position terminal block.

* Do not move any wires, only the metal jumpers

A.C. INPUT CONFIGURATION

multi-input chargers only)

A.C. INPUT CALIBRATION

CF-MTL-42403

CF-MTL-6003

208/452V

575V

225/480V

600V

240/506V

610V

CF-MTL-2401 /

42401

CF-MTL-

4803 / 6003

Calibrate the input tuning according to A.C. source by changing the postion
of the three (3) wires (A, B, C) on the nine (9) position terminal strip.

Calibrate the input tuning according to A.C. source by changing the
postion of the two (2) wires on the six (6) position terminal strip (A, A).

CF-MTL-2401

CF-MTL-42401

220V

208/452V

240V

225/480V

250V

240/506V

CHARGER INSTALLATION

Summary of Contents for CF-MTL-2401
















Search results

Summary of Contents for CF-MTL-2401

Reviews:

Related manuals for CF-MTL-2401

Brands by name

Popular brands

Tecnik CF-MTL-2401, User Manual

Search results

Summary of Contents for CF-MTL-2401

Reviews:

Related manuals for CF-MTL-2401

Brands by name

Popular brands