• VARIABLE SHADE CONTROL
After turn on the lens, short press “FUNC” button to choose “SHADE”, and adjust the lens
shade number. Use “ ” and “ ” buttons to select the lens shade in the dark state. The shade
range for each mode are as follows:
Cutting Mode
−
Shade 5 ~ 8 (See fig.15a)
Weld Mode
−
Shade 9 ~ 13 (See fig.15b)
Grind Mode
−
No. 4 only (See fig.15c)
Select the proper shade number for your welding / cutting process, by referring to the “Shade
Guide Table” on page 19.
• SENSITIVITY CONTROL
Press “FUNC” button to choose “SENSITIVITY”. Use “ ” and “ ” buttons to make the lens
more or less sensitive to arc light of different welding processes. Sensitivity setting 5-10 is
the normal setting for everyday use. The sensitivity ranges for each mode are as follows:
Cutting Mode
(Shade 5 ~ 8) /
Weld Mode
(Shade 9 ~ 13)
−
Sensitivity 0 ~ 10 (See fig.16a /
16b)
Grind Mode
− No sensitivity adjustment
As a simple rule for optimum performance, it is recommended to set sensitivity to the
maximum at the beginning and then gradually reduce it, until the filter reacts only to the
welding light flash and without annoying spurious triggering due to ambient light conditions
(direct sun, intensive artificial light, neighbouring welder's arcs etc.).
It may be necessary to adjust helmet sensitivity to accommodate different lighting conditions
or if lens is flashing On and Off. Adjust helmet sensitivity as follows: Adjust helmet sensitivity
in lighting conditions helmet will be used in.
• Press “ ” button to lower setting to 0.
• Face the helmet in the direction of use, exposing it to the surrounding light conditions.
• Press “ ” button repeatedly until the lens darkens, then press “ ” button until
lens clears.
Helmet is ready for use. Slight readjustment may be necessary for certain applications or if
lens is flashing on and off.
• DELAY CONTROL
Press “FUNC” button to choose “DELAY”, begin lens delay adjustments. Use the Lens Delay
Control “ ” and “ ” buttons to adjust the time for the lens to switch to the clear state after
welding or cutting.
Cutting Mode
(Shade 5 ~ 8) /
Weld Mode
(Shade 9 ~ 13)
−
Delay 0 ~ 10 (See fig.17a / 17b)
Grind Mode
− No sensitivity adjustment
The delay is particularly useful in eliminating bright after-rays present in higher amperage
applications where the molten puddle remains bright momentarily after welding. Use the
Lens Delay Control buttons to adjust delay from 0 to 10 (0.1 to 1.0 second). When welding
stopped, the viewing window automatically changes from dark back to light but with a
pre-set delay to compensate for any bright afterglow on the workpiece. The delay time /
response can be set from Level 0 to level 10. It is recommended to use a shorter delay
with spot welding applications and a longer delay with applications using higher currents.
Longer delays can also be used for low current TIG welding, and TIG / MIG / MAG pulse.
•
ADJUSTING THE FIT OF THE HELMET
The overall circumference of the headband can be made larger or smaller by rotating the
knob on the back of the headband (See adjustment “Y” in fig.18). This can be done while
wearing the helmet and allows just the right tension to be set to keep the helmet firmly on
the head without it being too tight.
•
If the headband is riding too high or too low on your head, adjust the strap which passes
over the top of your head. To do this release the end of the band by pushing the locking pin
out of the hole in the band. Slide the two portions of the band to a greater or lesser width
as required and push the locking pin through the nearest hole (See adjustment “W” in
fig.18).
•
Front and back bands will automatically self-adjust according to headform, and soft pads
suit forehead and back of head perfectly, which will bring more comfort (See fig.19a). Test
the fit of the headband by lifting up and closing down the helmet a few times while wearing
it. If the headband moves while tilting, re-adjust it until it is stable.
•
ADJUSTING THE DISTANCE BETWEEN THE HELMET AND THE FACE
Step 1: Press down and hold the “LOCK” latch on both sides (See fig.19b) and it can be
slide back and forth.
Step 2: Loosen the “LOCK” latch and keep it snap into slots. Please make sure the
distance between the lens to both eyes are equal, to avoid uneven darkness.
• ADJUSTING VIEW ANGLE POSITION
Tilt adjustment is located on right side of helmet. Loosen the right headgear tension knob
and adjust the lever forward or back to the proper position. Re-tighten the right headgear
tension knob (See fig.19c).
fig.22a
fig.22b
fig.23a
fig.23b
fig.23c
REPLACING THE OUTSIDE COVER LENS
Replace the outside cover lens if it is damaged. Place your fingernail in recess above filter
view window and flex lens upwards until it releases from edges of filter view window (See
fig.22a). When installing new outside cover lens, align one side of lens into the slot, and then
insert into the other side.
REPLACING THE INSIDE COVER LENS
Replace the inside cover lens if it is damaged. Place your fingernail in recess above filter
view window and flex lens upwards until it releases from edges of filter view window (See
fig.22b).
REPLACING THE GRINDING LENS AND GRINDING LENS COVER
Place
fingertips
into the gap around the grinding lens cover (See fig.23a), and flex the cover
upwards until it releases from helmet (See fig.23b). Press the grinding lens lightly and push
inward, remove the lens from slot and take it out carefully (See fig.23c). When installing new
grinding lens, put one side of lens into slot, and then insert into the other side. When
installing new grinding lens cover, put the side of lug boss of lens cover into the slot and then
lock the other side into the helmet. When hearing “click”, the lens cover is completely fixed.
REPLACING THE FACE SEAL
Press the “LOCK” key on cantilevered components and push the headgear in the direction
of arrow to separate headgear from the helmet (See fig.24a). In accordance with the order
of 1-4 in the figure, aligh the face seal with the velcro inside the helmet shell and make sure
the face seal is closely attached to helmet shell (See fig.24b). Then press the “LOCK” key on
cantilevered components to install the headgear to the helmet (See fig.24c), buckle up the
face seal according to 1-5 points (See fig.24d).
17