TECHWOOD TCL-12003 Instruction Manual Download Page 22

  22 

 

FIRST USE 

 

•  remove the appliance and all accessories carefully. 
•  Clean the outside of the appliance with a damp sponge or cloth and wipe it. 
•  Install the appliance on a table or flat, stable and horizontal surface. Make sure 

there is enough space to operate the machine properly. 

•  Unwind the power cord completely. 
•  Check that the voltage in the country where you are, corresponds to that 

indicated on the device. 

•  Connect the appliance to a good electrical outlet, (earthed if the appliance is 

class I), to avoid any danger. 

•  Disconnect the power cable from the power supply before performing 

maintenance, cleaning, and accessory mounting. 

•  Never modify the device. 

 

USE 

 
Cooling mode 

When the air conditioner goes into cooling mode, after turning on the power, the 
cooling indicator lights up. 
Press the "Up / Down" keys to set the desired temperature. (from 16 to 30 ° C). 
Press the "Speed" button to choose the speed. (Sweet or Strong) 

Fan mode 

By pressing the Mode key (2), it is possible to select the "Ventilation" mode. Press 
either the remote control or the control panel. the ventilation indicator lights up. 
Press the "Speed" button to choose the speed. (Sweet or Strong) 

Note: In this mode, temperature cannot be set. 
Dehumidifier mode 

By pressing the Mode key (2) it is possible to select the mode "Dehumidify". Press 
either on the remote control or on the control panel. the dehumidification indicator 
lights up. 
Remove the drain cork and insert one end of the hose to collect the drain water. 
The other end of the hose should be introduced into a suitable container such as a 
bottle or small jerry can. 
In dehumidification mode, when the temperature reaches 

17 

°

  C (62 

°

  F), the 

compressor starts. When the ambient temperature drops below 

15 

°

  C (59 

°

 

F), the compressor stops. When the temperature rises to an ambient temperature 
above 17 

°

  C, the compressor protection system will restart it 3 minutes later). 

Notes : In dehumidification mode : 
 

• the fan operates by default at low speed and the speed of the fan cannot   

Summary of Contents for TCL-12003





























Reviews: