TechVision PS32E8N2 Manual Download

Page: 52 / 121

PTZ

DVR User Manual

6.4 PTZ Protocol Setting

Click Start



Settings



Camera



PTZ



Protocol to go to the interface as shown below. You

can enable or disable the PTZ and set the protocol, baud rate and address of the analog dome in
the interface. Please make sure the analog speed dome camera is well connected to the DVR
before you control it.

Select the camera and enable PTZ and then set the protocol, baud rate and address of the dome
according to the settings of the dome.

Protocol

: The default communication protocol of the DVR is COC. Range from: PELCOP,

PELCOD, LILIN, MINKING, NEON, STAR, VIDO, DSCP, VISCA, COC, etc.

Address

: The address of the PTZ device.

Baud Rate

: Baud rate of the PTZ device. Range from: 110, 300, 600, 1200, 2400, 4800, 9600,

19200, 34800, 57600, 115200, 230400, 460800, 921600.

Summary of Contents for PS32E8N2


























































































































Search results

Summary of Contents for PS32E8N2

Reviews:

Related manuals for PS32E8N2

Brands by name

Popular brands

TechVision PS32E8N2, Manual

Search results

Summary of Contents for PS32E8N2

Reviews:

Related manuals for PS32E8N2

Brands by name

Popular brands