Techsis SL-224-H-P300 User Manual Download Page 7

 

 

 

 

 
 

 

 
 

 

 

 

 

SL-224-H-P300 

Tel

:021-22371482  

Fax

:021-66402031 

Www.techs.is  , [email protected] 

Page

7

 

 
 
1. 4 product appearance 

 

front panel  

   Contains indicator light, RJ45 port, SFP Port, DIP switch, RST button, Console port, as 
shown below 

 

 

indicator  
     

    The SL-224-H-P300 indicator works as shown in the following table. 
 

 

Indicators 

Title 

Color 

Work 
status 

Description 

POWER 

Power 
indicator 

Red 

Solid 

Power is normal 

Off 

No power, the power switch is not 
turned on, power supply is 
abnormal 

POE 

POE 

power 

indicator 

Red 

Solid 

The corresponding RJ45 port is 
connected to the powered device 
and the power supply is normal 

Off 

The corresponding RJ45 port is 
not connected to the powered 
device or the power supply is 
abnormal 

LINK/ACT 

Connection 

indicator 

Green 

Blinking  A  valid link is established  
Off 

An invalid link is established 

SYS 

System 

indicator 

Green 

Blinking  System is functioning properly  

Off 

System is functioning improperly 
Software is damaged 

Off 

An invalid link is established  on 
the SFP port 

 

 

Summary of Contents for SL-224-H-P300



















Reviews: