3.
Either press the SET key once more to enter the set mode for the time zone
and date section or do not touch any buttons for around 30 seconds to
confirm the set time.
Note:
The unit will still try to receive the signal every hour despite it being manually set.
When it does receive the signal, it will change the manually set time into the
received time. During reception attempts the DCF tower icon will flash. If reception
has been unsuccessful, then the DCF tower icon will not appear but reception will
still be attempted the following hour.
LCD 2 TIME ZONE AND DATE SETTING:
The second section of the LCD shows either the month and date, the weekday and
date, Alarm ((1)) time or Alarm ((2)) time. It also shows the Alarm ON/OFF icons
((1)) and ((2)).
TIME ZONE SETTING:
4.
To activate the alarm function, press the AL1 button once for Alarm 1. You
should now see the Alarm ((1)) symbol to represent the Alarm 1 being ON.
The time zone default of the Temperature Station is 0. To re-set the time zone:
1.
Press the SET key after entering the time setting in order to enter the Time
Zone setting (flashing).
2.
Using the IN key, set the time zone. The range runs from 0 to +9 and then
runs from -9 back to 0 in consecutive 1 hour intervals.
3.
Press the SET key to enter the date setting mode or do not touch any buttons
for around 30 seconds to confirm the time zone setting.
DATE SETTING:
Year (flashing)
Date (flashing) Month
Weekday Date
(flashing) (flashing) (flashing)
The date default of the Temperature Station is 1.1. or TH 1. in the year 1998. Once
the radio-controlled time signals are received, the date is automatically updated.
However, if the signals are not received, you can adjust the date manually. To do
this:
1.
Press the SET key after completing the time zone setting in order to enter the
year setting (flashing). Reset the year by pressing the IN key. The range runs
from 1998 to 2020.
2.
Press the SET key again to enter the month and date display (flashing).
3.
Using the OUT key, set the month required. Using the IN key, set the date
required.
4.
Press the SET key again to enter the weekday display (flashing).
5.
Using the IN key, set the weekday required.
6.
Press the set key once more to confirm all settings or do not touch any
buttons for around 30 seconds. The mode will return to normal.
ALARM SETTING:
1.
Press and hold down the AL1 key for around 3 seconds until the alarm time
display flashes.
2.
Use the IN key to set the hour and the OUT key to set the minutes. Pressing
these keys continuously moves the hours consecutively by 1 and the minutes
consecutively by 5.
3.
Either press the AL1 key once more to confirm and return to the normal
display or do not touch any buttons for around 30 seconds to confirm the set
time.
5.
To de-activate, press the AL1 button once again.
6.
The steps for setting, activating and de-activating Alarm 2 are the same, but
using the AL2 button instead of AL1.
SNOOZE SETTING AND STOPPING THE ALARM:
1.
When the alarm is sounding, press any one of the four keys SET, IN, OUT or
SNZ to activate the snooze function. The alarm will stop and re-activate after
the snooze interval of 5 minutes.
2.
To stop the alarm completely, press any one of the four keys AL1, AL2, DATE
or CH.
LCD 3 INDOOR TEMPERATURE:
The indoor temperature is received automatically and displayed on the third section
of the LCD.
TOGGLING AND RESETTING THE INDOOR RECORDINGS:
1.
To toggle between the indoor current, minimum and maximum temperature
data and the times at which they were recorded, press the IN key:
Once to show the minimum temperature values with time and date recorded.
Time Zone (flashing)
Indoor Temperature in ºC
