background image

3

Introduction

The  Cable  locator  «Success  CBI-116N»

 

is  the  detective-diagnostic  set,  intended  to  survey 

a  terrain  before  digging  or  excavation,  locating  electrical  cables  and  electrically  conductive 
underground utilities, determination of depth of their occurrence.

Benefits of the set

- Possibility to use in conditions of low temperatures,
- Wide Range of frequencies of band-pass filters (50/100/512/1024/8192/32768 Hz),

The application field

- Housing and public utilities
- Electricity networks
- Heating systems
- Water utilities
- Organizations conducting earthworks, etc.

Operating conditions

Ambient air temperature, °С ..................................... ........from -30 до +50
Relative humidity, % .......................... ...........................up to 85 at t=35 °С 
Atmospheric pressure, кPа ..............................................from 84 up to106 
Degree of protection against external influences................................ IP 54

1.2  The principle of operation

The principle of operation of the cable locator is based on phenomenon of electromagnetic 

induction.  The  electromagnetic  «EМD-247»  sensor  records  variable  electromagnetic  field 
which  is  being  produced  around  a  cable  under  research  of  it  or  a  pipeline  and  converts  an 
electromagnetic  signal  into  a  power  signal.  An  electrical  signal  enters  the  receiver,  where  it  is 
passing  amplification  and  filtering  (the  selection  signal  of  the  given  frequency.  The  location  of 
the maximum of electromagnetic field intensity measured above the ground, corresponds to the 
axis of the desired communication. The operator on the signal in the head phones and the LED 
indicator determines the location of the alignment and possible defects of communication. 

 

1 The general description

1.1 Composition of the set

1 - Receiver АP-014

    2 - Head phones

3 - The electromagnetic sensor  EMD-247

Summary of Contents for Success CBI-116N












Reviews: