TECHNO-MEDIA SAT-TV 40 User Manual Download Page 30 | Manualshive

Page: 30 / 33

TECHNO-MEDIA SAT-TV 40 User Manual Download Page 30

‘User Manual’’ Automatic Satellite Antennas TECHNO-MEDIA SRL

UMN_00094001

Rev 7

TECHNO-MEDIA SRL

Via IV Novembre 92 20021 Bollate (MI) tel. 02/48672988 - [email protected]

30

HOW TO UPDATE THE RECEIVER CHANNELS

As explained in the previous chapters, SAT-TV-40-65-80
is able to lock the satellite only if the receiver used was
previously  programmed  with  the  channels  and  the
satellite which the user would use. Anyway, it is possible
to  update  the  receiver  channels  after  the  antenna  is
pointed.

Follow these points in order to update your receiver:

1. Start a new search process setting your Set Top Box on a free channel (not

encrypted).

2. Wait that the antenna lock the satellite.

3. Press OFF button on the BeepBox version 2 BEEP-BOX.

During the Set Top Box update process, do not operate any button
on the Beep Box, do not switch on the antenna and do not turn on
the Ignition Key

4. To start the update process refer to the Set Top Box user manual..

5. Switch on the Antenna only at the end of the Set Top Box update process.

«
...
28
29
30
31
32
...
»

Summary of Contents for SAT-TV 40


































Reviews:

No comments