manualshive.com logo in svg

Techno-Isel Educational DaVinci, Setup, Page: 7 / 27

Share
Download
Techno-Isel Educational DaVinci Setup Download Page 7

vi

Contents

Chapter 1 General Set-Up And Assembly

General Instructions For Set-Up ..................................................................................... 2

Materials Checklist ................................................................................................ 2

Mounting The Spindle ........................................................................................... 3
Mounting The CAM Clamps And Clamp Bars ....................................................... 4
Initial Electrical Set-Up .......................................................................................... 5

Chapter 2 Safety Cover Installation

Installing The Safety Cover ............................................................................................. 8

Chapter 3 Software Installation

Installing The Software ................................................................................................. 10

Chapter 4 System Operation

Powering Up The DaVinci ............................................................................................. 12
Performing The DaVinci Self-Test................................................................................. 12
The Display Panel ......................................................................................................... 13

Error Codes ......................................................................................................... 13

Spindle Control Module ................................................................................................. 14

Manual Operation of Spindle Control .................................................................. 14
Software Operation of Spindle Control ............................................................... 14

Pal ........................................................................................................... 14
Direct Programming ................................................................................. 14

Chapter 5 Appendices

Appendix A: Wiring & Switch Settings ......................................................................... 16

Wiring Connections ............................................................................................. 16
Switch Settings .................................................................................................... 17

Adjusting The Baud Rate ......................................................................... 17
Adjusting The Acceleration Rate ............................................................. 18

Summary of Contents for Educational DaVinci




























Reviews:

No comments