Techno CNC Systems HD II Manual Download Page 8

14

Call: 1-631-648-7481 or Visit: support.technocnc.com

15

HD II Tabletop Manual

NK105G2

Call: 1-631-648-7481 or Visit: support.technocnc.com

HD II Tabletop Manual

NK105G2

3.7- Running a G-code file.

Once the XYZ origin has been set as per section 3.4 and the file has been loaded as per section 3.6 
the user is ready to run the G-code file. 

To run the G-code file simply press the start button 

 

Once the spindle has reached speed the machine will move into position to start the first cut.   

The file can be paused while running by pressing

To resume the file press                  .

To abort the file at any time press                .

Note: 
When the machine pauses, the spindle will stop and the Z axis will move to the Z clearance/
Safe height to allow inspection of the part.  

If the machine is jogged off the part during a pause, it will lose its position and when the file is 

resumed it will start from the new position. 

When using multiple tools it is best to create separate files for each tool.

 

 

The last file can be resumed at a breakpoint by pressing.

+

4.1- Alternating between Override and Programmed Feedrates.

IV. Advanced Tutorials. 

The controller can run G-code files with speed set by the user on the keypad, override speed, or with 
speed set in the CAM package/G-code file, programmed speeds. 

To determine what speed protocol will be used, do the following:

In the main screen, press menu                      to enter the menu screen .

Use the  

and 

 

key to scroll the cursor and highlight  

 
Press OK to select.

Use the  

 

and 

 

key scroll the cursor and highlight  

 
 
 
Press OK to select.

Note:
The F or S Option.  
F stands for Feed rates, and S stands for Spindle RPMS.

Note: 

“No” means speed in the G-code file will be obeyed.

 

 

“Yes” means speed will be overrode by the controller.

4. oper param

8. ignore F code

9. ignore S code

Summary of Contents for HD II















Reviews: