Technimount System Safety Arm System 500 User Manual Download Page 13

Page: 13 / 52

www.technimount.com

SAS UG 201912-R01

Return To Table of Contents

SPECIFICATIONS CONTINUED

installation holes on upper Base Plate

4 holes

recommended Loading Position

Lower

Recommended Number of Operators

Surface Base Mount Compatibility

Bracket Pro Standard and extended base

impact resistance Testing

30 G – 577 lbs

Typical Mounting

Clamp Block

Clamp box mounting with 4 screws on side square frame

Safety Arm

Dual locking system

• Red handle safety pin to pull arm up or down

• Lock pin for installation/removal

installation Time

5 minutes

estimated Time to remove Safety Arm

Less than 5 seconds

Standards for Testing

SAE J3043

ENVIRONMENTAL CONDITIONS

OPERATION

Temperature

-30 °F (-34 ° C) to 130 °F (54 °C)

Relative Humidity

Atmospheric Pressure

CAUTION

Any changes or modifications to the product will void the warranty.

Technimount system reserves the right to change specifications without notice.

Introduction

Summary of Contents for Safety Arm System 500





















































Search results

Summary of Contents for Safety Arm System 500

Reviews:

Related manuals for Safety Arm System 500

Brands by name

Popular brands

Technimount System Safety Arm System 500, User Manual

Search results

Summary of Contents for Safety Arm System 500

Reviews:

Related manuals for Safety Arm System 500

Brands by name

Popular brands