INSTALLATION - DMX CONNECTION
• Attention! The installation must be carried out by qualified service personnel only.
• Improper installation can result in serious injuries and /or damage to property.
• Overhead rigging requires extensive experience!
• Working load limits should be respected, certified installation materials should be
used, and the installed device should be inspected regularly for safety.
• Make sure the area below the installation place is free from unwanted persons during
rigging, de-rigging and servicing.
• Locate the fixture in a well ventilated spot, far away from any flammable materials and/
or liquids.
• The fixture must be fixed at least 50cm from surrounding walls.
• The device should be installed out of reach of people and outside areas where
persons may walk by or be seated.
• The device should be well fixed; a free swinging mounting is dangerous and should
not be considered!
• Do not cover any ventilation opening as this may result in overheating
• Before first time use it must be inspected by professional staff to ensure it is safe.
• A safety inspection should be performed regularly every year.
• Never expose the lens to direct sunlight, even for a short period. This may damage the
light effect or even cause a fire!
Connection between laser lights and DMX must use the shield cable of diameter greater
than 0.5mm. Please use the attached 3 pin XLR plug/socket to connect the DMX output/
input interface. The connection between socket and cable is shown below (note the plug/
socket’s 3 pin number and position).
• Note, XLR plug/socket’s 3 pin cannot be touched by inner hull, connection between
pins is not allowed. Except above connection, XLR plug/socket cannot be connected
with XLR control line. Device receives international standard DMX512(1990) control
signal.
• When using standard DMX512 control signal, the last device’s output interface must
be connected to a DMX plug. This plug is putting a 120-ohm resistance between
“canon” plug’s 2 pin and 3 pin. Shown in below diagram. Sticking this plug into the last
device’s signal output interface will avoid the interference during the process of signal
transmission.
DMX-Output
XLR Mounting-Sockets (Rear View)
DMX-Input
XLR Mounting-Plugs (Rear View)
1. Shield
2. Shield (-)
3. Shield (+)
Cable (EU)
Cable (EU)
Pin
International
Brown
Black
Live
L
Light Blue
White
Neutral
N
Yellow/Green
Green
Earth
- 4 -
installation
DMX connection
Connection
between
laser
lights
and
DMX
must
use
the
shied
cable
of
diameter
more
than
0.5mm.
Please
use
the
attached
3
pin
XLR
plug/socket
to
connect
the
DMX
output/input
interface.
The
connection between socket and cable as
below( note the plug/socket’
s 3 pin number and position).
DMX-output DMX-input
XLR mounting-sockets(rear view) XLR mounting-plugs(rear view)
1-
Shield
2-
Shield(- )
3-
)
Note,
XLR
plug/socket’
s
3pin
can
not
be
touched
by
inner
hull,
connection
between
pins
is
not
allowed.
Except
above
connection,
XLR
plug/socket
can
not
be
connected
with
XLR
control
line.
Device receives international standard DMX512(1990) control signal.
When
using
standard
DMX512
control
signal,
the
last
device’
s
output
interface
must
be
connected
to
a
DMX
plug.
This
plug
is
putting
a
120
ohm
resistance
between canon”
plug’
s
2
pin
and
3
pin.
Showing
as
below
pic.
Sticking
this
plug
into
the
last
device’
s
signal
output
interface,
it
will
avoid
the
interference
during
the
process
of
signal transmission.
- 4 -
installation
DMX connection
Connection
between
laser
lights
and
DMX
must
use
the
shied
cable
of
diameter
more
than
0.5mm.
Please
use
the
attached
3
pin
XLR
plug/socket
to
connect
the
DMX
output/input
interface.
The
connection between socket and cable as
below( note the plug/socket’
s 3 pin number and position).
DMX-output DMX-input
XLR mounting-sockets(rear view) XLR mounting-plugs(rear view)
1-
Shield
2-
Shield(- )
3-
)
Note,
XLR
plug/socket’
s
3pin
can
not
be
touched
by
inner
hull,
connection
between
pins
is
not
allowed.
Except
above
connection,
XLR
plug/socket
can
not
be
connected
with
XLR
control
line.
Device receives international standard DMX512(1990) control signal.
When
using
standard
DMX512
control
signal,
the
last
device’
s
output
interface
must
be
connected
to
a
DMX
plug.
This
plug
is
putting
a
120
ohm
resistance
between canon”
plug’
s
2
pin
and
3
pin.
Showing
as
below
pic.
Sticking
this
plug
into
the
last
device’
s
signal
output
interface,
it
will
avoid
the
interference
during
the
process
of
signal transmission.
- 4 -
installation
DMX connection
Connection
between
laser
lights
and
DMX
must
use
the
shied
cable
of
diameter
more
than
0.5mm.
Please
use
the
attached
3
pin
XLR
plug/socket
to
connect
the
DMX
output/input
interface.
The
connection between socket and cable as
below( note the plug/socket’
s 3 pin number and position).
DMX-output DMX-input
XLR mounting-sockets(rear view) XLR mounting-plugs(rear view)
1-
Shield
2-
Shield(- )
3-
)
Note,
XLR
plug/socket’
s
3pin
can
not
be
touched
by
inner
hull,
connection
between
pins
is
not
allowed.
Except
above
connection,
XLR
plug/socket
can
not
be
connected
with
XLR
control
line.
Device receives international standard DMX512(1990) control signal.
When
using
standard
DMX512
control
signal,
the
last
device’
s
output
interface
must
be
connected
to
a
DMX
plug.
This
plug
is
putting
a
120
ohm
resistance
between canon”
plug’
s
2
pin
and
3
pin.
Showing
as
below
pic.
Sticking
this
plug
into
the
last
device’
s
signal
output
interface,
it
will
avoid
the
interference
during
the
process
of
signal transmission.
