INSTALLATION
AC POWER LINKING
• Attention! The installation must be carried out by qualified service personnel only.
• Improper installation can result in serious injuries and /or damage to property.
• Overhead rigging requires extensive experience!
• Working load limits should be respected, certified installation materials should be
used, and the installed device should be inspected regularly for safety.
• Make sure the area below the installation place is free from unwanted persons during
rigging, de-rigging and servicing.
• Locate the fixture in a well ventilated spot, far away from any flammable materials and/
or liquids.
• The fixture must be fixed at least 50cm from surrounding walls.
• The device should be installed out of reach of people and outside areas where
persons may walk by or be seated.
• The device should be well fixed; a free swinging mounting is dangerous and should
not be considered!
• Do not cover any ventilation opening as this may result in overheating
• Before first time use it must be inspected by professional staff to ensure it is safe.
• A safety inspection should be performed regularly every year.
• Never expose the lens to direct sunlight, even for a short period. This may damage the
light effect or even cause a fire!
Connection between laser lights and DMX must use the shield cable of diameter greater
than 0.5mm. Please use the attached 3 pin XLR plug/socket to connect the DMX output/
input interface. The connection between socket and cable is shown below (note the plug/
socket’s 3 pin number and position).
Note, XLR plug/socket’s 3 pin cannot be touched by inner hull, connection between
pins is not allowed. Except above connection, XLR plug/socket cannot be connected
with XLR control line. Device receives international standard DMX512(1990) control
signal.
• When using standard DMX512 control signal, the last device’s output interface must
be connected to a DMX plug. This plug is putting a 120-ohm resistance between
“canon” plug’s 2 pin and 3 pin. Shown in below diagram. Sticking this plug into the last
device’s signal output interface will avoid the interference during the process of signal
transmission.
DMX-Output
XLR Mounting-Sockets (Rear View)
Please use the power cable supplied, note that power voltage and frequency are the
same as the marked voltage and frequency of device when connecting power. Every
device’s power should be connected separately, so that device can be controlled
individually.
The power cord specification table:
Cable (EU)
Cable (EU)
Pin
International
Brown
Black
Live
L
Light Blue
White
Neutral
N
Yellow/Green
Green
Earth
- 3 -
installation
Attention
The
installation
must
be
carried
out
by
qualified
service
personal
only.
Improper
installation
can
result
in
serious
injuries
and
/or
damage
to
property
.
Overhead
rigging
required
extensive
experience!
Working
load
limits
should
be
respected,
Certified
installation
materials
should
be
used,
the
installed
device should be inspected
regularly for safety.
Make
sure
the
area
below
the
installation
place
is
free
from
unwanted
persons
during
rigging,
de-rigging
and
servicing.
Locate
the
fixture
in
a
well
ventilated
spot,
far
away
from
any
flammable
materials
and/or
liquids.
The
fixture must
be fixed at least 50cm from surrounding walls.
The
device
should
be
installed
out
of
reach
of
people
and
outside
areas
where
persons
may
walk
by
or
be
seated.
The device should be well fixed; a free swinging mounting is dangerous and may not be considered!
Do not cover any ventilation opening as this may result in overheating
Before the first time use, it must be inspected by professional staff to make sure safety,
, inspection regularly
every
year.
Never
expose
the
lens
to
direct
sunlight,
even
for
a
short
period,
This
may
damage
the
light effect
or
even cause fire!
AC power linking
Please use the attached power, note that power voltage and frequency
are the same as the marked voltage and frequency of device when
connecting power. Every device’ s power should be connected separately,
so that device can be controlled individually.
The power cord specification table
Cable(EU)
Cable(US)
Pin
International
Brown
Black
Live
L
Liht blue
White
Neutral
N
Yellow/Green
Green
Earth
