background image

SAFETY INSTRUCTIONS

LASER SAFETY

•   If the external, flexible cable or cord of this product is damaged it must be replaced by 

a correct approved cable. 

•   Shields, lenses or ultraviolet screens should be changed if they become damaged to 

an extent that their effectiveness is impaired, for example by cracks or deep scratches.

•   Change the lamp if it is damaged or thermally deformed. 
•   After opening, carefully unpack the carton and check contents to ensure that all parts 

are in good condition. 

•   Contact the supplier or store of purchase immediately and retain packaging for 

inspection if any parts are damaged. 

•   Follow this user manual to operate this unit, making sure you are clear on all laser 

safety information and unit operation before powering it on. 

•   Incorrect operation will void warranty.

•   To protect the environment, please try to recycle the packing material as much as 

possible. 

•   The fixture is for indoor use only and rated IP20. Use only in dry locations. 
•   Keep this device away from rain and moisture, excessive heat, humidity and dust. 
•   Do not allow contact with water or any other fluids, or metallic objects. 
•   Don’t throw this product away just as general trash, please deal with the product by 

following the abandoned electronic product regulations in your country. 

•   Locate the fixture in a well ventilated spot, away from any flammable materials and/or 

liquids. 

•   The fixture must be fixed at least 50cm from surrounding walls. 
•   To avoid condensation forming inside, allow this unit to adapt to the surrounding 

temperatures when bringing it into a warm room after transport. 

•   Don’t install it on a flammable object. 
•   Do not use it when the maximum ambient temperature is higher than 40 degrees. 
•   Unplug the unit when it is not in use for a long period of time or before replacing the 

bulb. 

•   Do not open the top cover to avoid unit damage. 
•   Please use the original packing when the device is being transported.

•  According to EN 60825-1:2007, this product belongs to class 3B. 
•  Direct eye contact may cause injury. 
•  This product is for laser shows only. 
•  The class 3B laser light should be operated by a professional operator only. 
•    This is a show laser, emitting radiation with a wavelength spectrum between 400 and 

700nm and producing lighting effects for shows. 

•    International laser safety regulations require that the vertical height from installation to 

ground is more than 3 meters, horizontal distance is 2.5 meters from audience. 

•    Never direct the laser beam to people or animals and never leave this device running 

unattended. 

•    The legal requirements for using laser entertainment products vary from country to 

country. The user is responsible for the legal requirements at the location/country of 
use. 

•    Warning! Avoid direct eye contact with laser beams during operation, especially when 

the laser beams stay still, or injury to eyes may occur. 

•    Caution! The laser security measures are designed according to the specific terms 

of the relevant international laser safety standards and has the following laser safety 
protection means: 

 

Laser Key Switch: Laser is available only when the key is turned on. 

 

 Laser Emergency Switch: Remote connecting switch, it will cut off the laser 
light path instantly once the device is in a potential hazard. 

1 x Laser Light 
1 x Power Cord 
1 x Keys for switch 
1 x Interlock switch 
1 x User Manual

Summary of Contents for Rave SL-3410













Reviews: