Team Losi BND SUPER BAJA REY Instruction Manual Download Page 7

Page: 7 / 17

SUPER BAJA REY

DESERT TRUCK: 1:6 4WD BND, AVC • INSTRUCTION MANUAL

SPECIFICATIONS

Type

Sensorless

Constant/Peak

160A/1050A

Resistance

0.0002Ohm

Function

Forward with Brake, Forward/Reverse with Brake

Operation

Proportional forward, proportional reverse with braking

Input Voltage

3–8s LiPo

BEC Output

6V/8.4V, 6A

Overload Protection

Motor Lock-up protection, Low-voltage cutoff protection,
Thermal protection, Overload protection and fail safe (throttle
signal loss protection)

Dimensions (LxWxH)

70mm x 65mm x 45.5mm

Weight

288g

ESC LED STATUS

• No ESC LEDs will glow when there is no throttle input from the transmitter.
• The red ESC LED glows when there is any throttle input from the transmitter.

AUDIBLE WARNING TONES

1. Input Voltage:

The ESC checks the in put voltage when it is powered ON. If a voltage

problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause
(xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that
the battery power is not too low for safe operation.

2. Radio Connection:

The ESC checks radio signal input when it is powered ON.

If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause
(x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.

ESC FUNCTIONS

ESC CALIBRATION PROCEDURE

Ensure proper ESC function by calibrating the ESC to your transmitter inputs.
1. Power OFF the ESC.
2. Ensure your transmitter is powered ON, the throttle is not reversed, the

throttle trim is neutral and the throttle travel range is at 100%. Disable
any special functions such as ABS, etc.

3. Press the SET button while powering ON the ESC. Release the button as soon as the red

LED starts to flash.

4. Calibrate the throttle points by pressing the SET button once after each step.

- Neutral (1 flash)—leave the throttle at rest, untouched
- Full throttle (2 flashes)—pull the throttle fully back
- Full brake/reverse (3 flashes)—push the throttle fully forward

5. The motor will run 3 seconds after the last step is completed.

Tip:

If the motor turns in the wrong direction, reverse the connection of any 2 outside

motor wires. The center wire must remain in the center and cannot be moved to another
motor tab.

ESC PROGRAMMING PROCEDURE

1.  Connect a fully charged battery to the ESC.
2.  Power ON the ESC using the ESC switch.
3.  Hold the SET button for 1 second until the GREEN LED blinks, then release the SET button

to enter programming mode.

4. Press and release the SET button as needed to get to the desired menu option (the GREEN

LED will blink corresponding to the menu item number). Programming menu items 1
through 6 are accessible using the SET button on the ESC.

5. When at the desired menu item, hold the SET button for 3 seconds until the RED LED blinks.
6. Press the SET button to move among the settings based on how many times the RED LED

blinks (Refer to the table for more information).

7. Save the setting by holding the SET button for 3 seconds.
8. Power OFF the ESC switch and repeat the instructions above to change other settings.

DESCRIPTIONS

1. Running Mode

Forward Only with Brake

Intended for competition use, this mode allows only forward and brake controls.

Forward/Reverse with Brake

This mode is the basic all-around mode, allowing forward, reverse and brake controls.
To engage reverse while moving forward, apply the brake until the vehicle has come to
a complete stop, release brake, then apply the brake again. While braking or in reverse,
engaging the throttle will result in the vehicle immediately accelerating forward.

2. Li-Po Cells

The default setting is

Auto Calc

, which will automatically select the detetected number

of cells. Select value 2–5 to manually select a cell count from 3–8 cells.

3. Low Voltage Cutoff

This function helps to prevent battery over-discharge. The ESC continuously monitors the
battery’s voltage. If the voltage falls below the voltage threshold for 2 seconds, the output
power shuts off and the red LED flashes twice repeatedly.
The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries,
if the voltage battery pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery
pack; if it is lower than 9.0V, it will be treated as a 2-cell Li-Po battery pack. Example: for a
8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po
battery pack and the low-voltage cut-off threshold will be 5.2V (2.6x2=5.2).

4. Bec Voltage

Select either 6 or 8.4 V to run the receiver and servos.

5. Max Brake Force

Adjusts the maximum braking force. A higher value provides stronger braking, but can
also cause the wheels to lock, resulting in loss of control of the car.

6. Max Reverse Force

This parameter adjusts the maximum power when travelling in reverse.

7. Start Mode (Punch)

Sets the initial throttle punch when the car accelerates. Level 1 gives a very soft initial
acceleration and level 5 gives a stronger initial acceleration.

8. Timing

Allows for timing value selection according to your motor. Generally, higher timing value
brings out higher power output, but the efficiency of the system will be slightly lower with
possible increases in motor and ESC running temperatures.

The black-shaded setting is the factory default.

PROGRAMMABLE ITEMS

PROGRAMMABLE VALUE