ii
i
ii
ii
ii
ii
ii
ii
ii
ii
ii
INTRO
INTRO
Team Losi Racing is continually changing and improving designs; therefore, the actual part may appear slightly diff erent than the illustrated part. Illustrations of parts
and assemblies may be slightly distorted to enhance pertinent details.
TOOLS REQUIRED FOR ASSEMBLY
Team Losi Racing has supplied all necessary Allen wrenches and special wrenches that are needed for assembly and adjustments. The following
common tools will also be required: needle-nose pliers, regular pliers, hobby knife, scissors or other body cutting/trimming tools, and a soldering iron
may be necessary for radio installation. 3/16", 1/4", 5/16" and 11/32" nut drivers are optional.
RADIO/ELECTRONICS
A suggested radio layout is provided in this manual. Your high-performance RC center should be consulted regarding specifi c questions pertaining to
radio/electrical equipment.
HARDWARE IDENTIFICATION
When in question, use the Hardware Identifi cation Guide at the back of this manual.
• For screws, the prefi x number designates the thread size and number of threads per inch (e.g., 4-40 is a #4 size thread with 40 threads per inch).
The second number, or fraction, designates the length of the screw. For cap head and button head screws, this number refers to the length of the
threaded portion of the screw. For fl at head and setscrews, this number refers to the overall length of the screw.
• Bearings and bushings are referenced by the inside diameter (I.D.) x outside diameter (O.D.).
• Shafts and pins are designated by type (Roll, Solid) and referenced by diameter x length.
• Washers, Spacers and Shims are described by inside diameter or the screw size that will pass through the inside diameter x the thickness or by their
designated application (e.g., Ball Stud washer is primarily used under a Ball Stud).
• Retaining Clips are sized by the shaft diameter that they attach to or by type (Body). The Hardware Icon associated with E/C-clips only designates
the part genre of clips, not the actual part.
• Nuts come in four types, Non-Flanged, Flanged (F), Plain and Locking (L) (designated on the Hardware Icons). The prefi x number designates the
thread size and number of threads per inch. The second number, or fraction, designates the size of the hex. For example, L 4-40 x 1/4" designates a
locknut that will thread onto a 4-40 screw using a 1/4" nut driver.
• Setscrews come in three types, Cup (C), Flat (F) and Oval (O) (designated on the hardware Icons). The prefi x number designates the thread size and
number of thread per inch. The second number, or fraction, designates the length of the threaded portion of the screw.
TABLE OF CONTENTS
SECTIONS
1.
INTRODUCTION
......................................................
i
Important Safety Notes .....................................
i
Vehicle/Manual
Organization
...........................
ii
Tools Required for Assembly ............................
ii
Radio/Electronics
..............................................
ii
Hardware
Identifi cation ....................................
ii
2.
Step A:
Steering Assembly .................................. 1-2
3.
Step B:
Front Clip ............................................... 3-8
4.
Step C:
Center Transmission ............................. 9-12
5.
Step D:
Rear Clip ............................................ 13-18
6.
Step E:
Shocks ................................................ 19-21
7.
Step F:
Radio Tray .......................................... 22-26
8.
Step G:
Engine Installation ............................. 27-30
9.
Step H:
Wheels, Tires, Body ........................... 31-33
8.
Checklist Before Your First Run
........................34
9.
Setup Guide
.................................................... 35-37
10.
Warranty Information
................................... 38-39
11.
Blank 8IGHT-T 2.0 Setup Sheet
.........................40
12.
Hardware Identifi cation Guide
...........................41
13.
Filled-out 8IGHT-T 2.0 Vehicle Setup Sheet
......42
TABLES
Table 1:
8IGHT-T 2.0
Completed Vehicle Specifi cations
i
Table 2:
Servo Installation .................................................. 23
Note: Final vehicle weight will vary depending on accessories used.
8IGHT-T 2.0 COMPLETED KIT SPECIFICATIONS
*All measurements taken at ride height (36mm).
Overall Chassis Length: 18.75" (476mm)
Wheelbase: 14.93"-15.09" (379-383mm)
*Front Track Width: 16.375" (419.9mm)
Overall Length w/Tires: 22.075" (573mm)
*Overall Height: 7.30" (185.5mm)
*Rear Track Width: 16.375" (415.9mm)
Table 1: 8IGHT-T 2.0 Completed Vehicle Specifi cations.
Vehicle/Manual Organization:
The vehicle is composed of diff erent steps marked A through H. Each step contains all of the parts necessary to complete a particular section of the
vehicle. Some of these steps have sub-assembly steps within them. It is helpful to read through the instructions for an entire step prior to working on
your vehicle. Next to each of the step numbers is a check box. At the completion of each step, place a check in this box so that if you must stop and
come back to the assembly, you will be able to pick up where you left off .
For your convenience, an actual-size Hardware Identifi cation Guide is included as a fold-out page at the back of this
manual. Hardware that is not easily diff erentiable in each step is called out with an icon which contains a small picture
of the part genre (referenced on the Hardware Identifi cation Guide), the quantity of that part required for what is
shown in the step, and the size or name of that part. To check a part, hold it against the silhouette until the correct part
is identifi ed. Associated with each of these parts, in the Hardware Identifi cation Guide, is an LOSA-Number which is used when ordering replacement
parts for your 8IGHT-T 2.0. In some cases, extra hardware has been supplied for parts that may be easy to lose.
Components used in each step are identifi ed by their relative LOSA-Number and the component’s name. With the exception of a few parts, these are
not referenced in the Hardware Identifi cation Guide.
The molded parts in Team Losi Racing vehicles are manufactured to demanding tolerances. When screws are tightened to the point of being snug, the
parts are held fi rmly in place. For this reason, it is very important that screws not be overtightened in any of the plastic parts.
In some steps there will be a fi lled black circle with a white number. These indicate the specifi c order by which assembly must occur. In cases where
steps are repeated (front/rear or left/right) these numbers may be omitted. Please note that these numbers will not call out every sub-step required for
the step’s assembly procedures, they will only highlight the critical order required for assembly.
In each step, there are specifi c “Detail Icons” (shaped like a stop sign) that call out critical precautions or assembly tips for the process. There is a
reference key that describes the meaning of each of the icons located on the fold-out Hardware Identifi cation Guide at the back of this manual.
To ensure that parts are not lost during construction, it is recommended that you work over a towel or mat to prevent parts from rolling away.
