background image

 

T5919

 

 

Page 19 of 22 

Document Number: DS-000363

 

Revision: 1.0 

 

 

HANDLING INSTRUCTIONS   

PICK AND PLACE EQUIPMENT 

The MEMS microphone can be handled using standard pick-and-place and chip shooting equipment. Take care to avoid damage to the 
MEMS microphone structure as follows: 

 

Use a standard pickup tool to handle the microphone. Because the microphone hole is on the bottom of the package, the 
pickup tool can make contact with any part of the lid surface. 

 

Do not pick up the microphone with a vacuum tool that makes contact with the bottom side of the microphone.  
Do not pull air out of or blow air into the microphone port. 

 

Do not use excessive force to place the microphone on the PCB. 

 
REFLOW SOLDER 

For best results, the soldering profile must be in accordance with the recommendations of the manufacturer of the solder paste used to 
attach the MEMS microphone to the PCB. It is recommended that the solder reflow profile not exceed the limit conditions specified 
in Figure 2 and Table 7. 
 

BOARD WASH 

When washing the PCB, ensure that water does not make contact with the microphone port. Do not use blow-off procedures or 
ultrasonic cleaning. 
 

Summary of Contents for MMICT5919-00-012























Reviews: