manualshive.com logo in svg

Taylor-Wharton MicroBulk MB-450, Installation And Operation Manual, Page: 19 / 27

Share
Download
Taylor-Wharton MicroBulk MB-450 Installation And Operation Manual Download Page 19

BT- 434 Rev.A

19

 MAINTENANCE

Routine inspections of the system are recommended. The need for maintenance usually becomes appar-

ent from inspection and indications of improper operation. Typical trouble indications include leakage 

from valves or piping connections and excessive venting through relief valves. Keep a permanent log of 

all inspections and repairs performed. Such a log can be valuable in evaluating performance and schedul-

ing maintenance.

Date

Nature of Work (Describe in Full)

Remarks

Service men’s Signature

Always observe the safety precautions at the front of this manual and follow the instructions given in this

section. Before working on the system, properly empty the vessel of liquid and relieve pressure on the 

vessel and piping. Do not allow unqualified persons to attempt repairs on this equipment. Refer to the 

Trouble - Remedy Guide in this manual for assistance in troubleshooting.

Figure 9: Inspection and Repair Log (Sample Form)

 Leak Test

 Globe Valves

 Regulator

After making repairs requiring disassembly or replacement of components, leak test all valves or piping 

joints that were taken apart and reconnected. Apply leak detector fluid to the test surface. Large leaks 

instantly form large bubble clusters, while fine leaks produce white foam that builds up more slowly. All 

leaks must be repaired and retested before the system is returned to service.

All of the globe valves (V-1, V-2, V-3, & V-4) are an integral part of the system and are not easily removable. 

However, the valves may be rebuilt without removal from the system. All of the globe valves use the same

rebuild kit. The Taylor-Wharton part number for the rebuild kit is 1750-9C35. All valve components, except

the body, are provided in the kit.

A dual stage, spring-loaded regulator (PCV-1) is employed for the pressure building/economizer circuit. 

The regulator may be adjusted without removal from the system. The following procedure describes the 

process: 

Summary of Contents for MicroBulk MB-450




























Reviews:

No comments