Brakes
Page 60
B0-150-00 and MX-016-00
MB-150-03
This section is one section of a complete service
manual. Before starting any procedure, read all
warnings and instructions that are located in the
Service Guidelines chapter.
WARNING
REAR DRUM BRAKE, INSPECT/
REPLACE
NOTE: It is recommended that both the left and
right brake pads be replaced as a set.
Service Limits
Refer to the table at the end of this section
Inspection
1: Raise the rear of the vehicle and support with
jack stands.
2: Remove the rear wheels.
3: Measure the brake lining (not including the metal
backing plate) of each shoe at it’s thinnest point.
If any one of the shoes are equal to or less
that the service limit then all shoes should be
replaced.
4: Measure the drum inner diameter in three places.
If the diameter is less than the service limit then
the drum must be replaced.
5: Lower the vehicle.
6: Reconnect the battery, remove the blocks from
behind the wheels and test drive.
Brake Adjuster Assembly
Do not allow grease to contact any of the braking
surfaces. Braking surfaces contaminated with grease
may cause the brakes to fail resulting in property
damage and/or severe bodily injury.
WARNING
Replace
1: Release the park brake.
2: Raise the rear wheels off of the ground and
support with jack stands.
3: Remove the tire/wheel assembly. Refer to
Tires
and Wheels
section for information on removing
the wheel.
4: Remove and inspect the brake drum. Refer
to
Inspect the Service Brake
section for
information regarding inspecting the brake drum.
5: Remove the retracting springs and torsion springs
from the brake shoes.
6: Remove the hair pin clips from the actuating arms
and discard.
7: Remove the brake shoes and brake adjustor
assembly from the backing plate.
8: Thoroughly clean and inspect the adjustor
assembly. Replace parts as required.
9: Apply a
very light
coating of high temperature
grease to the adjustor screw threads.
10: Install in reverse order.
11: Repeat for the opposite side.
12: Adjust the brakes. See
Adjust the Service
Brakes
section for information regarding
adjusting the brakes.
13: Set the park brake.
14: Reconnect the main positive and negative at the
batteries.
15: Lower the wheels to the ground.
16: Remove the blocks from behind the wheels.
17: Release the park brake and test drive the vehicle.
Summary of Contents for B0-150-00
