50
Downstream line X1, Ohm/km
X1
0.0000
–2.0000
0.0001
0.3500
Downstream line X0, Ohm/km
X0
0.0000
–4.0000
0.0001
1.5000
Maximum fault distance, km
Lm
0.0
–1000.0
0.1
1.0
Table 82
– Ring line recloser FL element settings
Settings
Designation
Range
Step size
Default
Operating mode+
Mode+
Enable/Disable
n.a.
Disable
Downstream line X1+, Ohm/km
X1+
0.0000
–2.0000
0.0001
0.3500
Downstream line X0+, Ohm/km
X0+
0.0000
–4.0000
0.0001
1.5000
Maximum fault d, km
Lm+
0.0
–1000.0
0.1
1.0
Operating mode-
Mode-
Enable/Disable
n.a.
Disable
Downstream line X1-, Ohm/km
X1-
0.0000
–2.0000
0.0001
0.3500
Downstream line X0-, Ohm/km
X0-
0.0000
–4.0000
0.0001
1.5000
Maximum fault distance-, km
Lm-
0.0
–1000.0
0.1
1.0
Cold Load Pickup (CLP)
In some cases, when power supply is restored after prolonged outage, this results in greater than normal
power demand. The main cause of this problem is the large number of electric heaters, furnaces, refrigerators,
air conditioners and other thermostat-controlled loads. Higher current is often seen by protection as short circuit
or overload, that result in circuit breakers automatically tripping to protect the system from overload, and the
power goes off again. The CLP element enables temporary increasing current pickup setting to sustain cold
load current and avoid tripping without compromising protection sensitivity. This functionality is applicable for
radial recloser as only in this case can the duration of power interruption for a group of customers be observed.
CLP settings are described in Table 83.
Table 83
– CLP element settings
Parameter
Designation
Range
Resolution
Recognition time, min
Trec
0
–60
1
Reset time, min
Tres
1
–400
1
Cold load multiplier
CLM
1.0
–2.0
0.1
4.2 Measurement
Overview
The Main Processor gets the analog signals from the Outdoor Switching Module current and voltage sensors,
converts them into digital format, and filters it for Harmonic content. The RMS values of the filtered signals are
used for protection and indication as shown in the table below.
Table 84
– Applicability of RMS values of the signals
Settings
Designation
Range
Resolution
Applicability
Protection Indication
Phase currents, A
Ia, Ib, Ic
0 … 12500
1 A
Residual current
16
, A
In
0 … 12500
0.1 A
Positive sequence current, A
I1
0 … 12500
1 A
Negative sequence current, A
I2
0 … 12500
1 A
Neutral voltage shift measured from side, kV
Un+
0 … 30
0.1 kV
Neutral voltage shift measured from Source - side, kV
Ub-
0 … 30
0.1 kV
Positive sequence voltage measured from side, kV
U1+
0 … 30
0.1 kV
Positive sequence voltage measured from Source - side, kV
U1-
0 … 30
0.1 kV
Negative sequence voltage measured from side, kV
U2+
0 … 30
0.1 kV
Negative sequence voltage measured from Source - side, kV
U2-
0 … 30
0.1 kV
Frequency measured from side
17
, Hz
F+
40-60 at 50Hz
40-70 at 60Hz
0.01 Hz
16
Residual current In is equal to three times the zero sequence current Io.
17
Voltage and frequency memory is used if all three phase to earth voltages on any side drop below approximately 0.5 kV.
Summary of Contents for Rec15
