Taurus TF-SR Assembly And Operating Instructions Manual Download Page 21 | Manualshive

Page: 21 / 48

background image

3

1

25

21

11

22

24

19

13

23

21

Step 8:

Assembly of guide rod

1. Fasten the first guide rod (19) with one small rubber pad (21), one smith bar hook (22), one

medium rubber pad (23), one guide bar sleeve (24) and one sliding sleeve (25) between bending

tube (1) and back upright tube (3) by using one bolt (11) and one washer (13).

2. Repeat this step for the other guide rod.

«
...
19
20
21
22
23
...
»

Summary of Contents for TF-SR

















































Reviews:

No comments

Related manuals for TF-SR

ACS880-01 Series

Brand: ABB Pages: 238

Brand: NARGESA Pages: 50

Brand: Ultimaker Pages: 38

Brand: A&D Pages: 2

Brand: A&D Pages: 176

Brand: Gaspardo Pages: 16

Brand: Gastrodomus Pages: 4

Brand: HANYOUNG NUX Pages: 2

Brand: Gastrodomus Pages: 39

SC 2 Deluxe EasyFix

Brand: Kärcher Pages: 12

Brand: Kärcher Pages: 16

Brand: V-TAC Pages: 13

Brand: Emos Pages: 8

Brand: Kärcher Pages: 60

Brand: XPOtool Pages: 4

Brand: Harken Pages: 78

Brand: ALLSPEEDS Pages: 22

Brand: Master Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands