Taurus TF-SR Assembly And Operating Instructions Manual Download Page 15 | Manualshive

Page: 15 / 48

background image

15

Step 2:

Assembly of the front and back upright tube

1. Fasten the first front upright tube (2) on the bending tube (1) by using two bolts (11), two lock

nuts (12) and four washers (13).

2. Fasten the first back upright tube (3) on the same bending tube (1) by using two bolts (11), two

lock nuts (12) and four washers (13).

3. Repeat these steps for the other side.

«
...
13
14
15
16
17
...
»

Summary of Contents for TF-SR

















































Reviews:

No comments

Related manuals for TF-SR

Brand: Campbell Pages: 18

Brand: Vector Pages: 4

Brand: Wavetek Pages: 74

Brand: Fairchild Pages: 16

Brand: Parker Research Corp Pages: 4

Brand: Eastwood Pages: 20

Brand: Daihan Scientific Pages: 43

Brand: OAKWORKS Pages: 2

Brand: Oakton Pages: 2

Brand: Oakton Pages: 2

Brand: O2matic Pages: 4

Brand: ZOLL Pages: 37

Brand: Wacker Neuson Pages: 34

Brand: Wagan Pages: 4

Brand: Wachs Pages: 22

Brand: ABB Pages: 33

Brand: Salter Pages: 18

Brand: Salter Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands