Taurus Dual Pro Bicep Curl & Tricep Assembly And Operating Instructions Manual Download Page 7

Page: 7 / 44

GENERAL INFORMATION

1.1

Technical Data

Weight and Dimensions

Packaging dimensions (L x W x H) and article weight (gross, incl. packaging):
Box 1:

163 cm x 91 cm x 19.5 cm

25 kg/ 55 lbs

Box 2:

152 cm x 89 cm x 28.5 cm

35 kg/ 55 lbs

Box 3:

144 cm x 62 cmx 53.5 cm

80 kg/ 176 lbs

Box 4:

70 cm x 16 cm x 48 cm

10 kg/ 22 lbs

Box 5 (weight plates):

30.5 cm x 11.5 cm x 12.5 cm

70.5 kg/ 155 lbs total

Set-up dimensions (L x W x H):

112 cm x 125 cm x 148 cm

Article weight (net, without packaging):

188.5 kg/ 416 lbs

Maximum user weight:

180 kg/ 397 lbs

Cables and Pulleys

Weight

stack:

Weight plates:

14 + 1 (4.5 kg/ 10 lbs)

Cable

material:

Steel

Cover

material:

Nylon

Cable

length:

380.5

Transmission

ratio:

1:2

Pulley

diameter:

89/114

Summary of Contents for Dual Pro Bicep Curl & Tricep













































Search results

Summary of Contents for Dual Pro Bicep Curl & Tricep

Reviews:

Related manuals for Dual Pro Bicep Curl & Tricep

Brands by name

Popular brands

Taurus Dual Pro Bicep Curl & Tricep, Assembly And Operating Instructions Manual

Search results

Summary of Contents for Dual Pro Bicep Curl & Tricep

Reviews:

Related manuals for Dual Pro Bicep Curl & Tricep

Brands by name

Popular brands