Taurus Dual Pro Bicep Curl & Tricep Assembly And Operating Instructions Manual Download Page 20 | Manualshive

Page: 20 / 44

background image

No.

Name

Specification Qty.

83

Socket cap screw

M8*30

4

84

Socket cap screw

M8*75

2

98

Spring washer

M8

6

101

Flat washer

8

106

Back pad

1

108

Arm pad

1

110

Seat pad

1

20

Bicep Curl & Tricep

Step 5:

Assembly of the Back Pad, Arm Pad and Seat Pad

1. Fix the back pad (106) to the seat pad frame (38) with two screws (83), two spring washers (98)

and two flat washers (101).

2. Fix the seat pad (110) to the seat pad frame (38) with two screws (83), two spring washers (98)

and two flat washers (101).

3. Fix the arm pad (108) to the upright frame (39) with two screws (84), two spring washers (98)

and two flat washers (101).

«
...
18
19
20
21
22
...
»

Summary of Contents for Dual Pro Bicep Curl & Tricep













































Reviews:

No comments

Related manuals for Dual Pro Bicep Curl & Tricep

Brand: T-Rex Pages: 13

Brand: Datex-Ohmeda Pages: 80

Brand: MacDon Pages: 2

Brand: V-TAC Pages: 6

Brand: Tascam Pages: 8

Synthesis SDEC-3000

Brand: JBL Pages: 24

Brand: Xilica Audio Design Pages: 30

Brand: TEC Pages: 6

Brand: U Technology Pages: 6

Brand: U-Line Pages: 3

Brand: U-Line Pages: 2

REBOUND DUAL ST

Brand: Össur Pages: 104

Brand: Össur Pages: 130

Brand: Masterclock Pages: 19

Brand: Beurer Pages: 21

Brand: SCHUNK Pages: 35

AURO SPOT CLAS100

Brand: Cameo Pages: 60

Brand: Biosonic Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands