m
6.4 Forward/Reverse switch (Fig. 6 / Item 2)
With the slide switch above the On/Off switch you
can select the direction of rotation of the battery
powered drill/screwdriver and secure it against
being switched on accidentally. You can choose
between clockwise and anticlockwise rotation. To
avoid causing damage to the gearing it is advisable
to change the direction of rotation only when the
tool is at a standstill. The On/Off switch is blocked
when the slide switch is in centre position.
6.5 On/Off switch (Fig. 6 / Item 3)
Infinitely variable speed control is possible with the
On/Off switch. The further you press the switch, the
higher the speed of the battery-powered
drill/screwdriver.
6.6 Battery capacity indicator (Fig. 5/Item 10)
Press the button for the battery capacity indicator
(11). The battery capacity indicator (10) indicates the
charge state of the battery on 3 colored LEDs.
All LEDs illuminate:
The battery is fully charged.
The yellow and red LED illuminate:
The battery has an adequate remaining charge.
Red LED:
The battery is empty, recharge the battery.
6.7 Changing the tool (Fig. 7)
Important.
Set the changeover switch (2) to its
centre position whenever you carry out any work
(for example changing the tool, maintenance work,
etc.) on the cordless drill.
•
The cordless drill is fitted with a quickaction
chuck (7) with an automatic spindle stop.
•
Open the chuck (7). The chuck opening (a)
must be large enough to hold the tool (drill bit
or screwdriver bit).
•
Select the suitable tool. Push the tool as far as
possible into the chuck opening (a).
•
Tighten the chuck (7) and then check that the
tool is secure.
6.8 Screwdriving
We recommend using self-centering screws (e.g.
Torx screws, recessed head screws) designed for
reliable working. Be sure to use a bit that matches
the screw in shape and size. Set the torque, as
described elsewhere in these operating instructions,
to suit the size of screw.
6.9 Selecting 1st gear to 2nd gear (Fig. 5/Item 6)
By adjusting the selector switch, you can work with
a faster or slower turning speed. Change the gear
only when the drill is at a standstill. If you fail to
observe this point, the gearing may be damaged.
7. Cleaning, maintenance
and ordering of spare parts
Always pull out the mains power plug before
starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could
attack the plastic parts of the equipment.
Ensure that no water can seep into the
device.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8. Disposal and recycling
The unit is supplied in packaging to prevent its
being damaged in transit. This packaging is raw
material and can therefore be reused or can be
returned to the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local
council.
TAURUS TITANIUM
®
is a registered trademark of
ALDI Stores.
ALDI Guarantee
Specially made for ALDI Stores to our stringent
quality specifications. If you are not entirely
satisfied with this product, please return it to
your nearest ALDI store within 60 days from the
date of purchase for a full refund or replacement,
or take advantage of our after sales support by
calling the Customer Service Hotline.
Einhell Australia Pty. Ltd.
6/166 Wellington St
Collingwood,
Victoria, 3066
Australia
01/2011
8
After Sales Support TEL: 1300 922 271 EMAIL: [email protected]
