m
Important!
The vibration value changes according to the
area of application of the electric tool and
may exceed the specified value in exceptional
circumstances.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect
working order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the
appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever
necessary.
•
Switch the appliance off when it is not in
use.
•
Wear protective gloves.
5. Before starting the
machine
Be sure to read the following information before
you use your cordless drill for the first time:
1.
Charge the battery pack with the charger
supplied.
2.
Only ever use screwdriver bits which are
suitable for the purpose and in faultless
condition.
3.
Always check for concealed electric cables
and gas and water pipes when drilling and
screwing in walls.
6. Operation
6.1 Charging the LI battery pack (Fig. 2/3/4)
The battery is protected from exhaustive
discharge.An integrated protective circuit
automatically switches off the equipment when
the battery is flat. In this case the bit chuck will
cease to turn.
Warning!
Do not press the ON/OFF switch any
more if the protective circuit has actuated. This
may damage the battery.
1.
Remove the battery pack (4) from the
handle, pressing the pushlock buttons (5) on
the left and right sides to do so.
2.
Check that your mains voltage is the same
as that marked on the rating plate of the
battery charger. Plug the mains plug of the
charger (9) into the mains socket outlet.
1.
Remove the battery pack (4) from the
handle, pressing the pushlock buttons (5) on
the left and right sides to do so.
2.
Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Plug the mains plug of the charger
(9) into the mains socket outlet.
3.
Connect the charging cable (a) to the
charging adapter (8).
4.
The green LED on the charger will come
on. Plug the battery (4) into the charging
adapter (8). Now the red LED will come on
to indicate that the battery pack is being
charged. When the charging period is
completed after approx. 3 hours, the red
LED goes out again. The temperature of the
battery (4) may rise during the charging
operation. This is normal.
If the battery pack fails to become charged, please
check
•
whether there is voltage at the socket-outlet
•
whether there is good contact at the
charging contacts of the battery station (8).
If the battery still fails to become charged, please
return
•
the charger and charging adapter
•
the battery pack to our Customer Service
Department.
To ensure that the LI battery pack provides long
service you should take care to recharge it
promptly. You must recharge the battery pack
when you notice that the power of the cordless
drill drops.
Never fully discharge the battery pack. This will
cause the LI battery pack to develop a defect.
6.2 Torque setting (Fig. 5 / Item 1)
The cordless drill is fitted with a mechanical
torque selector.
The torque for a specific size of screw is selected
with the set-collar (1). The correct torque depends
on several factors:
•
on the type and hardness of material in
question
•
on the type and length screws used
•
on the requirements needing to be met by
the screwed joint.
The clutch disengages with a grating sound to
indicate when the set torque is reached.
Important! The tool must be at a standstill when
you set the torque with the setting ring.
6.3 Drilling (Fig. 5 / Item 1)
For drilling purposes, move the set-collar to the
laststep “Drill“. In this setting the slip clutch is
inactive. The maximum torque is available in
drilling mode.
7
Warning!
Do not press the ON/OFF switch any
more if the protective circuit has actuated. This
may damage the battery.
After Sales Support TEL: 1300 922 271 EMAIL: [email protected]
