4
13
2.6
3.
“
CONTROL
”
output
Service of the control unit
The control unit is equipped with the CONTROL relay whose contacts can be used e.g. to switch off
another heat source when the fireplace works. The
parameter defines the
function of the relay more precisely. (see PARAMETERS LEVEL 3)
CONTROL relay turned off
CONTROL relay turned on
There are elements on the control panel (fig. 2). In the turn-off state only the orange stanby state
LED (7) lights and the graphic display shows current temperature of the water jacket and current
time. The turn-on of the control unit follows by pressing the button ( ) ON/OFF
. In order to turn
it off press once more the button ( )and at the same time hold it down for about 1sec. In case of
supply voltage decline the control unit comes back to the state before the decline.
The operation state is presented on the graphic display ( ). The screens inform about the operation of
devices, temperature of sensors; they make it possible to change the parameters etc..The change of
screen is done by pressing the CHOOSE button ( ). If this is the screen that is able to change a
parameter, press the CONFIRM button ( ) , which causes blinking of the parameter field to be
changed. By pressing
“
+
”
( )or
“
-
”
( ) one can alter its value.
If there are more parameter fields on the screen (e.g. setting the clock) then one will go among them
by pressing the CHOOSE button ( ). By clicking the CONFIRM button ( ) one confirms the changes
- the parameter field stops blinking.
The changed parameter not confirmed for 10 secs is not accepted by the control unit and it recalls a
previous value of the parameter.
The button F2-ESC (8) is for cancelling a current operation and going over to the screen of the
fireplace.
<12> CONTROL Relay
3
3
2
7
6
4
5
7
6
!
!
Fig.2 Control panel view
Connection cable of the control may be replaced only
by producer or his authorized service locations
WARRANTY
WARNING !
ANY MODIFICATION OF THE CONTROL UNIT MADE BY A USER CAN
BE THE CAUSE OF SAFETY CONDITIONS DETERIORATION AND CAN
EXPOSE THE USER TO ELECTRIC SHOCK OR DAMAGE DEVICES
SUPPLIED
.
Date of sale
Seller's signature and stamp
Zak
ł
ad elektroniczny TATAREK Jerzy Tatarek
50-559 Wroclaw, 75 Swieradowska st
ph. (071) 367-21-67, 373-14-88, fax 373-14-58; tax index number 899-020-21-48;
Bank account : BZ WBK S.A. O/WROC
Ł
AW 6910901522-0000-0000-5201-9335
www.tatarek.com.pl.; E-mail: [email protected]
1.Warranty is valid [24] months from the date of sale.
2.Producer does not take responsibility for any mechanical damages made by user.
3.MAKING REPAIRS OR MODYFYING THE DEVICE BY USER IS
FORBIDDEN AND CAUSES WARRANTY CANCELATION
4.Warranty card is valid only with date of sale, seller's signature and stamp
5.Warranty and after-warranty repairs should be done only by producer, damaged
regulators should be sent to producer in order to make all repairs needed.
6.Warranty protection includes the EU
7.Warranty does not exclude, not restrict and not suspend buyer
’
s rights coming from
the incompatibility of the article with the agreement (Laws Journal No. 141 Pos. 1176)
WARNING!
1. Producer does not take the responsibility for damage
caused by atmospheric discharge
2. and overvoltage in the mains
3. Burnt fuses are not subject to warranty replacement
Register No.. GIOS: E 0002240WZ
Worn out electronic
and electric devices must be transfered to
the utilization collection place, where will
be accepted for free
ARGO-FILM
Recycling Plant No. 6
180 Krakowska st., 52-015 Wroclaw
ph.: 071 794 43 01,
0 515 122 142
“ON/OFF”
“CHOOSE”
“CONFIRM”
