29
I25
I24
I23
I22
I21
I20
I19
I18
tr
th
sl
se
tr
sv
pt
pl
no
nl
it
fr
fi
es
en
de
cz
Service, maintenance and care
The correct maintenance of the machine is a precondition for error-free
operation and a long service life.
Service intervals
TASKI machines are high quality machines that have been checked for safety
at the factory by authorised inspectors. Electrical and mechanical components
are subject to wear and/or ageing after longer periods of use.
Service centre
Should you contact us due to a malfunction or for placing an order, please
always state the type, description and the serial number of your machine.
You can find this information on the name plate of your machine, and the
address of your nearest TASKI partner can be found on the last page of this
manual.
Blade change on the swingo 3500
Blade on the inner radius.
Blade on the outer radius
Replacing fuses
Replacing main fuse:
Caution:
Only TASKI branded spare parts must be used, otherwise
warrenties and liabilities will be omitted!
Symbols:
◊
= After use,
◊◊
= every week,
◊◊◊
= every month,
⊗
= Service light
Activity
◊ ◊◊ ◊◊◊
⊗
page
Recharge batteries
25
Refill distilled water (wet batteries).
Please follow the manufacturers instructions of
use booklet for these batteries!
25
Drain and clean the recovery tank
27
Clean the suction filter
30
Clean the recycling filter (optional)
28
Check solution supply pipe and filter and clean if
necessary
24
Drain and clean the solution tank (Flextank) using
fresh water
27
Clean the tools
28
Clean squeegee, check whether the blades are
worn and replace if necessary
28
Clean the machine with a damp cloth
28
Clean the full recovery tank probe and check that
it is functioning properly
Clean seal of the tank hood, check for cracks and
replace if necessary.
Maintenance programs by TASKI service made by
TASKI technician
• In order to ensure operational reliability and
availability for use, the service must be carried
out when the service indicatior lights up (factory
setting 650 working hours) or at least once a
year.
S
horter intervals may be necessary
u
nder rough or extreme working
conditions and/or in case of insufficient maintenance.
• Place the clean squeegee unit with the outer radius face down on a solid
surface e.g. table, floor.
• Press one hand onto the squeegee body by the hose connector.
• Grasp the blade with your thumb and forefinger in the middle of the arch and
pull strongly until the metal band clicks open and the blade is released from
the squeegee body.
• Release the metal strap and pull the blade off the squeegee body.
• Clean squeegee (body, metal straps and blades) with a brush under running
water.
• Mount the ‘‘turned‘‘ or the new blade on the squeegee body, so the ridges
point outwards.
• Hook the metal strap into place (Check position of mounting slots) and press
the centre of it until it clicks into place and presses the blade onto the
squeegee body.(Risk of injury)
• Turn the squeegee upside down by placing it on its suction hose connector
and the bumper wheels.
• Release the fixation screw of the blade holder using a screwdriver (Allen
screw).
• Release the metal band and pull the blade off the squeegee body.
• Clean squeegee (body, metal straps and blades) with a brush under running
water.
• Mount the ‘‘turned‘‘ or the new blade onto the squeegee body.
• Hook the metal strap into place (check position of mounting slots) and fix it
with the screwdriver until the blade is pressed onto the squeegee body.
• The shape of the blades allow them to be used on all sides before needing
replacement.
• Pull out the key and apply the parking brake (refer to page 25).
• Push the driver seat forward so that it rests on the steering wheel, and open
the battery cover.
• Disconnect the battery from the machine using the battery disconnection
mechanism.
Caution:
Use fuses with the correct value only!
Wrong fuses can cause damage to the machine.
• Loosen insulating nut (19mm spanner) of battery pole.
• Remove red insulating nut and detach the
battery charger leads.
• Remove and replace main fuse.
Fuse ratings:
co 2500/3500
Main fuse
125A (Pudenz)
• Mount battery charger leads onto the battery pole and mount the insulating
nut of battery pole.
• Reconnect the battery plug to the machine.
• Re-cover the battery compartment and return
the driver seat into its normal position.
