Task Force Tips ZCF1T3 Instructions For Installation Manual Download Page 12

Page: 12 / 24

©Copyright Task Force Tips LLC 2014-2018

LIZ-060 October 26, 2020 Rev03

4.3 MONITOR COMPATIBILITY AND INSTALLATION

A series of TFT Industrial Monitors has been created specifically for use with the Booster, Hydrant Under Monitor, and Industrial Valve

Under Monitor. These monitors are specified by adding the –Z suffix to the desired model of TFT Monsoon, Typhoon or Hurricane (e.g.

Y5-DP1A-Z). Models with –Z suffix are the only monitors verified to be compatible with the Booster. All TFT Industrial Monitors feature

American Red powder coating and monitor base heights chosen to work well with the Booster, HUM and IVUM. In addition, all Industrial

Monsoons and Typhoons include aluminum crank handles on each worm-drive control.

Figure 4.3

WARNING

Exceeding safe operating range could cause pressure vessels to rupture and result in injury.

• Do not install shutoff valves downstream of Booster.

• Do not exceed the lowest maximum operating pressure rating of any devices assembled

together.

• Do not exceed the lowest maximum flow of any of the devices assembled together.

• Do not install monitor extension pipes between Booster and monitor such as Task Force Tips

Extend-A-Gun, Akron 3406, or Elkhart Extender.

• Do not exceed 20” (508 mm) monitor height measured from bottom edge of monitor inlet (flange

or female thread) to centerline of monitor outlet. Examples of acceptable and forbidden

monitors are illustrated below.

[
[

Booster ZCH-series

(ZCH1T3 shown)

11.4" [289mm]

Monitor heights

less than

20" [508mm]

are acceptable

Industrial Valve

Under Monitor

9.5" [241mm]

TFT

Industrial Monitors

with -Z suffix

are recommended

(all models are

less than 20" tall)

Booster ZCH-series

(ZCH1T1 shown)

9.2" [234mm]

Hydrant

Under Monitor

10.5" [265mm]

Monitor heights

greater than

20" [508mm]

are FORBIDDEN

Monitor

extension pipes

above Booster

are FORBIDDEN

Booster ZCF-series

(ZCF1T3 shown)

13.4" [339mm]

Summary of Contents for ZCF1T3

























Search results

Summary of Contents for ZCF1T3

Reviews:

Related manuals for ZCF1T3

Brands by name

Popular brands

Task Force Tips ZCF1T3, Instructions For Installation Manual

Search results

Summary of Contents for ZCF1T3

Reviews:

Related manuals for ZCF1T3

Brands by name

Popular brands