background image

©Copyright Task Force Tips LLC 2010-2021

8

LIY-250 May 10, 2021 Rev03

TASK FORCE TIPS LLC

MADE IN USA · tft.com 

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 · 219-462-6161 · Fax 219-464-7155

7.0 MAINTENANCE

TFT  products  are  designed  and  manufactured  to  be  damage  resistant  and  require  minimal  maintenance.  However,  as  the  primary

firefighting tool upon which your life depends, it should be treated accordingly. The unit should be kept clean and free of dirt by rinsing

with water after each use. Any inoperable or damaged parts should be repaired or replaced before placing the unit in service. To help

prevent mechanical damage, do not drop or throw equipment. 
In applications where appliances are left continuously connected to the apparatus or other devices or are used where water is trapped

inside the appliance, the appliance must be flushed with fresh water following each use and inspected for damage.
This appliance should be disconnected, cleaned and visually inspected inside and out at least quarterly, or as water quality and use may

require.  Moving  parts  such  as  handles,  valve  ball  and  couplings  should  be  checked  for  smooth  and  free  operation.  Seals  shall  be

greased as needed with Silicone based grease such as Molykote 112. Any scrapes that expose bare aluminum should be cleaned and

touched up with enamel paint such as Rust-Oleum. Replace any missing or damaged parts before returning to service. 
Any equipment taken out of service due to failure should be returned to the factory for repair or replacement. If you have any questions

regarding the testing or maintenance of your valve, please call Task Force Tips at 800-348-2686. 

7.1 SERVICE TESTING

In accordance with NFPA 1962, equipment must be tested a minimum of annually. Units failing any part of this test must be removed

from service, repaired and retested upon completion of the repair. 

7.2 REPAIR

Factory  service  is  available  with  repair  time  seldom  exceeding  one  day  in  our  facility.  Factory  serviced  equipment  is  repaired  by

experienced technicians, wet tested to original specifications, and promptly returned. Any returns should include a note as to the nature

of the problem and whom to reach in case of questions.
Repair parts and service procedures are available for those wishing to perform their own repairs. Task Force Tips assumes no liability for

damage to equipment or injury to personnel that is a result of user service. Contact the factory or visit the web site at tft.com for parts

lists, exploded views, test procedures and troubleshooting guides.  
Performance tests shall be conducted on the equipment after a repair, or anytime a problem is reported to verify operation in accordance

with TFT test procedures. Consult factory for the procedure that corresponds to the model and serial number of the equipment. Any

equipment which fails the related test criteria should be removed from service immediately. Troubleshooting guides are available with

each test procedure or equipment can be returned to the factory for service and testing. 

8.0 EXPLODED VIEWS AND PARTS LISTS

Exploded views and parts lists are available at tft.com/serial-number.

WARNING

Service  technicians  bear  responsibility  for  ensuring  use  of  appropriate  protective  clothing  and

equipment. The chosen protective clothing and equipment must provide protection from potential

hazards users may encounter while servicing equipment. Requirements for protective clothing and

equipment are determined by the Authority Having Jurisdiction (AHJ).  

CAUTION

Any alterations to the product or its markings could diminish safety and constitutes a misuse of 

this product. 

NOTICE

All replacement parts must be obtained from the manufacturer to assure proper operation of the 

device. 

Summary of Contents for LIY-250









Reviews: