background image

2

1.0

2.0

3.0

3.1

3.2

4.0

4.1
4.2

5.0

5.1
5.2

5.3

MEANING OF SIGNAL WORDS

SAFETY

GENERAL INFORMATION

CORROSION

USE WITH SALT WATER

INSTALLATION

MOUNTING ON TRUCK
CHANGING HANDWHEEL TO LEFT SIDE

USE

INTAKE ELBOW
VALVE POSITION INDICATOR

STORZ SUCTION GASKET REQUEST

1.0 MEANING OF SIGNAL WORDS

A safety related message is identified by a safety alert symbol and a signal word to indicate the level of risk involved
with a particular hazard. Per ANSI standard Z535.4-1998 the definitions of the three signal words are as follows:

DANGER

CAUTION

WARNING

DANGER indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.

2.0 SAFETY

CAUTION

WARNING

CAUTION

Kinks in supply hose may reduce water flow and cause injury or death to persons
dependant on water flow. When this valve is used on a hydrant or fire truck it is
recommended that it be used with an elbow to minimize risk of hoseline kinks.

Maximum operating pressure 250 PSI (17 bar). Do not exceed 250 PSI on either
side of the valve.

Valve must be properly connected. Mismatched or damaged connectors may
cause leaking or uncoupling under pressure and could cause injury.

6.0

7.0

7.1
7.2

9.0

10.0

11.0

AIR VENT AND WATER DRAIN

PRESSURE RELIEF VALVE

SETTING PRESSURE
FLOW vs. PRESSURE CURVE

BALL INTAKE VALVE PRESSURE LOSS

WARRANTY

8.0

DRAWINGS AND PARTS LISTS

MAINTENANCE

TABLE OF CONTENTS

WARNING

Injury or death can result from burst hoses and fittings. Be sure the pressure
relief valve is set at the proper pressure for the type of hose and equipment you
are using. See NFPA 1961 and NFPA 1962.

WARNING

This equipment is intended for use by trained personnel for firefighting. Its use
for other purposes may involve hazards not addressed by this manual. See
appropriate guidance and training to reduce risk of injury.

LIA-200 March 17, 2004 Rev 5

©Copyright Task Force Tips, Inc. 2002-2004

Summary of Contents for Ball Intake Valve









Reviews: